Chemical Vapor Deposition of Wide-Bandgap p-Type Semiconductor Cuprous Iodide for Optoelectronic Device Applications
Eliza Kate Spear,Christina Marie Chang,Luke M. Davis,Roy G. Gordon
DOI: https://doi.org/10.1149/ma2022-01311306mtgabs
2022-07-15
ECS Meeting Abstracts
Abstract:Continuous, pinhole-free thin films of transparent conductive materials (TCMs) with p- and n-type conductivity are critical components of optoelectronic devices including photovoltaics (PV), transparent electronics, and LEDs [1]. TCMs with n-type conductivity are widely available in the form of semiconducting oxides [2]; however, p-type TCMs (hole transport materials, HTMs) with suitable conductivity are comparatively rare [1]. Particularly in the rapidly growing field of thin film perovskite PV, device-quality thin films of HTMs with high stability and conductivity are urgently needed to replace the organic HTMs typically employed in perovskite PV research [3]. As such, techniques to deposit inorganic HTM thin films are desired. With a focus on applying HTMs in optoelectronic devices at the commercial scale, these materials must be deposited by a scalable technique yielding thin, continuous, pinhole-free films. Chemical vapor deposition (CVD) is a highly scalable thin film deposition technique widely used in industry, with a proven ability to yield high-quality thin films on large-area substrates [4]. A variety of n-type TCMs are accessible by CVD techniques, but few CVD methods exist for p-type TCMs; examples include atomic layer deposition of NiO x and VO x [5]. The cuprous halides (CuX, X = Cl, Br, I), which are optically transparent p-type semiconductors with bandgaps ~3 eV, are promising inorganic HTM candidates. Cuprous iodide is of particular interest due to its low resistivity (~10 -2 Ohm·cm), high hole concentration and mobility (~10 19 cm -3 and ~1-10 cm 2 V -1 s -1 , respectively), and its valence band maximum position (ionization potential: 5.0-5.4 eV), which is well-aligned with common perovskite absorber materials [6]. While CuI crystallite arrays have been obtained by metal-organic CVD [7], CVD of continuous CuI thin films has only been achieved by a two-step vapor conversion process, requiring initial deposition of a copper chalcogen followed by vapor-phase conversion to the halide [6]. Our group has recently published a CVD technique enabling direct deposition of continuous CuBr thin films via CVD reaction between hydrogen bromide and vinyltrimethylsilane(hexafluoroacetylacetonato)copper(I) [Cu(hfac)(vtms)] [8], and this technique has been extended to deposition of CuI. X-ray photoelectron spectroscopy indicates pure CuI films with an atomic ratio of approximately 1:1 Cu:I, and x-ray diffraction confirms deposition of γ-CuI. Similar to our observations for CuBr films, substrate identity has significant effects on CuI film continuity. Progress towards CVD of continuous CuI films on substrates of interest for practical application in optoelectronic devices will be discussed, with a particular focus on perovskite PV. [1] A. N. Fioretti and M. Morales-Masis, "Bridging the p-type transparent conductive materials gap: synthesis approaches for disperse valence band materials," J. Photon. Energy, 10, 042002 (2020). [2] M. Morales-Masis, S. De Wolf, R. Woods-Robinson, J. W. Ager, and C. Ballif, "Transparent Electrodes for Efficient Optoelectronics," Adv. Electron. Mater., 3, 1600529 (2017). [3] B. Gil, A. J. Yun, Y. Lee, J. Kim, B. Lee, and B. Park, "Recent Progress in Inorganic Hole Transport Materials for Efficient and Stable Perovskite Solar Cells," Electron. Mater. Lett., 15, 505 (2019). [4] R. Gordon, "Chemical Vapor Deposition of Coatings on Glass," J. Non-Cryst. Solids, 218, 81 (1997). [5] J. A. Raiford, S. T. Oyakhire, and S. F. Bent, "Applications of atomic layer deposition and chemical vapor deposition for perovskite solar cells," Energy Environ. Sci., 13, 1997 (2020). [6] R. Heasley, L. M. Davis, D. Chua, C. M. Chang, and R. G. Gordon, "Vapor Deposition of Transparent, p-Type Cuprous Iodide Via a Two-Step Conversion Process," ACS Appl. Energy Mater., 1, 6953 (2018). [7] V. Gottschalch, S. Blaurock, G. Benndorf, J. Lenzner, M. Grundmann, and H. Krautscheid, "Copper iodide synthesized by iodization of Cu-films and deposited using MOCVD," J. Cryst. Growth, 471, 21 (2017). [8] C. M. Chang, L. M. Davis, E. K. Spear, and R. G. Gordon, "Chemical Vapor Deposition of Transparent, p-Type Cuprous Bromide Thin Films," Chem. Mater., 33, 1426 (2021).