Abstract:In recent years, arc-based additive manufacturing techniques have been enthusiastically accepted for fabricating components made of various structural materials. In this work, a functionally graded material (FGM) structure of pure copper (Cu) and stainless steel (SS316L) was developed using cold metal transfer-based wire arc additive manufacturing (CMT-WAAM). Components combining Cu and steel show great usage in many industries since they combine high corrosion resistance, ductility, thermal conductivity, and wear resistance to the excellent mechanical properties. The CMT-WAAM fabricated FGM was well built and shows no deformation, bulging, and cracking in the graded region. Microstructural and elemental mapping analysis studies shows that Fe was deposited over Cu matrix in the gradient region and a gradual grain size and compositional gradient was observed. The phase analysis doesn't reveal formation on any metastable or intermetallic phase at the interface. The mechanical properties of the printed structure were analyzed by room temperature tensile testing, Charpy impact test and microhardness measurements in both scanning and build directions. The FGM samples show an average ultimate tensile strength of 641 ± 10.06 MPa vs 427 ± 5.03 MPa and elongation to fracture percentage of 19.8 ± 1.13% vs 21.8 ± 1.56% in scanning and build directions, respectively. The average Charpy toughness of fabricated FGM was 57.88 ± 2.86 J vs 46.24 ± 1.46 J in scanning and build directions, respectively. The tensile and impact strengths of FGM samples were higher than as fabricated pure Cu samples but lower than as fabricated SS316L samples and the fracture was dominated by ductile mode of fracture. The strength and ductility of CMT-WAAM fabricated SS316L-Cu FGM was significantly high and may allow use of these materials in engineering and industrial applications.

Microstructure and Properties of Wcp/Cu Layered Functionally Graded Materials Prepared by Vacuum Hot-Pressed Sintering

Fabrication and microstructure of W/Cu functionally graded material

Fabrication of W–Cu Functionally Graded Material with Improved Mechanical Strength

Functionally Graded W-Cu Materials Prepared from Cu-Coated W Powders by Microwave Sintering

Investigation for the Fracture Process of WCp/Cu Functionally Graded Materials under Three-Point-Bending

Synthesis of Functionally Graded AA7075-B4C Composite with Multi-Level Gradient Structure

HIGH HEAT LOAD PROPERTIES OF W/Cu FUNCTIONALLY GRADED MATERIALS

Fast fabrication of W-Cu functionally graded material by high-gravity combustion synthesis and melt-infiltration

Characterization and forming process of a functionally graded WC-Co/Ni composite

Fabrication and Micro-Structure of a Multilayer Functionally Graded (wc–co)–ni Composite

Fabrication and properties of W-Cu functionally graded materials by tape calendaring method

Fabrication of Diamond/w–cu Functionally Graded Material by Microwave Sintering

Fabrication Of Sic/Cu Functionally Gradient Material By Graded Sintering

Composition design and mechanical properties of B 4 C/Al-Zn-Mg-Cu functionally graded materials prepared by laser additive manufacturing

Preparation and characterization of Al2O3–Ti3SiC2 composites and its functionally graded materials

Microstructures and mechanical properties of the bilayer functionally graded WC-TiC-Ni/Co cemented carbides

Microstructural and mechanical properties examination of SS316L-Cu functionally graded material fabricated by wire arc additive manufacturing

Fabrication and Properties of Axisymmetric WC/Co Functionally Graded Hard Metal via Microwave Sintering

Characterization of a bilayer WC–Co hardmetal using Hertzian indentation technique

Improved parallelism of graded W–Cu–SiC materials by adjusting the coefficient of thermal expansion

Microstructures and mechanical properties of functionally graded TiCN–TaC ceramics prepared by a novel layer processing strategy