Abstract:Copper (Cu)-stainless steel (SS 304L) multi-material is enduring research topic for various engineering applications such as tooling industry, aerospace, power-generation and cryogenic applications. Laser directed energy deposition (LDED) based additive manufacturing is a one of the promising technologies for fabricating Cu-SS multi-material component. However, LDED of Cu-SS is difficult due to the significant difference in thermo-physical properties and poor solubility of Cu and Fe. One of the methods to overcome this issue is adopting a functionally graded material (FGM) approach. In this pretext, the fabrication of Cu-SS FGM using the LDED process is taken up in the present study with three different Cu compositional grading approaches, such as direct (GD100Cu), 50 % (GD50Cu) and 20 % (GD20Cu). The LDED process windows for single tracks and bulk deposition of Cu-SS FGM are identified by varying the laser power, scan speed and composition of Cu and SS304L. Subsequently, the identified process window is used to deposit bulk structures of Cu-SS FGM. The LDED-built Cu-SS FGMs are characterized in terms of build quality, chemical composition, microstructural evolution and mechanical behavior. Microscopic analysis reveals, the defect-free deposition of GD100Cu and GD50Cu, at identified process parameters. For GD20Cu, the micro-crack formation in the graded region and inter-layer porosity in the Cu-rich region are two competing phenomenon, and it is observed that layer-wise increase in laser power and interlayer delay leads to minimum crack density and lower porosity. Further, increase in Cu content leads to significant change in microstructural morphology from columnar dendrites to fine cellular morphology. In Cu-SS FG structures, the chemical composition and mechanical properties are found to be changing gradually. Further, obtained ultimate tensile strength (UTS) of GD100Cu and GD50Cu is found higher than GD20Cu and the mode of failure is found to be ductile. The improved UTS in GD100Cu and GD50Cu in comparison with pure Cu arises due to formation of nano precipitate of Cu in the inter-dendritic zone of Fe rich phase. This establishes the suitability of LDED for building FG Cu-SS components at GD50Cu over GD20Cu.

Microstructural and mechanical properties examination of SS316L-Cu functionally graded material fabricated by wire arc additive manufacturing

Characterization of Functionally Graded Material (Stainless Steel 347/308L) Fabricated through Wire and Arc Additive Manufacturing: Microstructure and Mechanical Perspectives

Microstructure and Mechanical Properties of 304L Steel Fabricated by Arc Additive Manufacturing

Fabrication and characterization of stainless steel 308 L / Inconel 625 functionally graded material with continuous change in composition by dual-wire arc additive manufacturing

Microstructural Features and Mechanical Integrity of Wire Arc Additive Manufactured SS321/Inconel 625 Functionally Gradient Material

Dual-Wire Plasma Arc Additively Manufactured SS 316L-Inconel 625 Functionally Graded Material: Microstructure Evolution and Mechanical Properties

Microstructural and mechanical properties analysis of SS 316L structure fabricated using CMT-wire arc additive manufacturing

Fabrication and Fatigue Properties of Dissimilar Steel Functionally Graded Material Structure Through Wire Arc Additive Manufacturing

Microstructure and Mechanical Properties of P21-STS316L Functionally Graded Material Manufactured by Direct Energy Deposition 3D Print

A functionally graded material from stainless steel 304 to Fe–40Al fabricated by dual wire arc additive manufacturing

Investigation on dual wire TIG Arc additive manufacturing of IN625 and SS316L FGM for continuous gradient and sandwich structures

Microstructure and tribological behaviour of dissimilar steel functional structure developed via arc-based DED process

Elucidating laser directed energy deposition based additive manufacturing of copper-stainless steel functionally graded material: Processing and material behavior

Effect of composition gradient design on microstructure and mechanical properties of dual-wire plasma arc additively manufactured 316L/IN625 functionally graded materials

Experimental characteristics of 316L stainless steel thin wall processed in wire-based arc additive manufacturing process

The Formability and Mechanical Properties of 316L Stainless Steel Fabricated by Pulsed Arc Swing Additive Manufacturing

Deposition of Functionally Graded Material Fabricated by Robot Plasma Arc Welding

Microstructure and Texture of 2205 Duplex Stainless Steel Addi-Tive Parts Fabricated by the Cold Metal Transfer (CMT) Wire and Arc Additive Manufacturing (WAAM)

Experimental study of shielding gas concentration on mechanical properties of stainless steel alloy parts using wire and arc additive manufacturing

Functional grading of low alloy steel to 316 L by Wire Arc Additive Manufacturing – Microstructural and mechanical characterization of bi-metal interface

Fabrication and microstructure of W/Cu functionally graded material