Abstract:Functionally graded materials (FGMs) are composites comprising various materials that can overcome the limitations of homogeneous materials, such as abrupt property changes at material interfaces. This results in gradual changes in the microstructure and composition, thus limiting the performance optimization under complex operating conditions. In this study, a novel ultrasonic-assisted double wire arc additive manufacturing (U-DWAAM) process is performed to fabricate stainless steel 308 L (SS 308 L) and Inconel 718 (In 718) composites with and without ultrasonic treatment. The microstructure, chemical composition, tensile strength, and hardness of the fabricated FGMs are investigated with and without ultrasonic treatment. The results show that the microstructure of the FGMs without ultrasonic treatment is mainly composed of columnar grains. However, by performing ultrasonic treatment, the grain size reduced, the homogeneity improved, and the grains refined into equiaxed grains. The chemical composition shows a smooth transition from SS 308 L to In 718, with an increase in Ni, the main element in In 718, and a decrease in Fe, the main element in SS 308 L. Typical epitaxial grain growth is observed at interfaces with different compositions. For the specimens subjected to ultrasonic treatment, their tensile strength is slightly higher and elongation lower compared with those of the specimens without ultrasonic treatment. This is attributable to the change in the equiaxed grains and a decrease in the crystal size owing to the application of ultrasound in the columnar grains. The hardness increases gradually from the SS 308 L portion of the FGMs as the mixing ratio of In 718 increases. With and without ultrasonic treatment, the percentage increase in hardness is 7%, 9%, 10%, 12%, and 15%, compared with that of the same layer without ultrasonic treatment. The increase in hardness is due to microstructural changes (equiaxed grains in the columnar phase), solid solution strengthening, and precipitation enhancement owing to an increase in Ni, Mo, and Nb contents with the In 718 content.

Dual-Wire Plasma Arc Additively Manufactured SS 316L-Inconel 625 Functionally Graded Material: Microstructure Evolution and Mechanical Properties

Fabrication and characterization of stainless steel 308 L / Inconel 625 functionally graded material with continuous change in composition by dual-wire arc additive manufacturing

Effect of composition gradient design on microstructure and mechanical properties of dual-wire plasma arc additively manufactured 316L/IN625 functionally graded materials

Deposition of Functionally Graded Material Fabricated by Robot Plasma Arc Welding

Study on Optimization Strategy for the Composition Transition Gradient in SS 316L/Inconel 625 Functionally Graded Materials

Microstructural Features and Mechanical Integrity of Wire Arc Additive Manufactured SS321/Inconel 625 Functionally Gradient Material

Investigation on dual wire TIG Arc additive manufacturing of IN625 and SS316L FGM for continuous gradient and sandwich structures

Microstructural and mechanical properties examination of SS316L-Cu functionally graded material fabricated by wire arc additive manufacturing

Characterization of Functionally Graded Material (Stainless Steel 347/308L) Fabricated through Wire and Arc Additive Manufacturing: Microstructure and Mechanical Perspectives

Influence of composition gradient variation on the microstructure and mechanical properties of 316 L/Inconel718 functionally graded material fabricated by laser additive manufacturing

A functionally graded material from stainless steel 304 to Fe–40Al fabricated by dual wire arc additive manufacturing

A functionally graded material design from stainless steel to Ni-based superalloy by laser metal deposition coupled with thermodynamic prediction

Fabrication and Fatigue Properties of Dissimilar Steel Functionally Graded Material Structure Through Wire Arc Additive Manufacturing

The effects and utility of homogenization and thermodynamic modeling on microstructure and mechanical properties of SS316/IN718 functionally graded materials fabricated by laser-based directed energy deposition

Effect of synchronous electromagnetic stirring on Laves phase morphology and mechanical property of Inconel625-HSLA steel functionally graded material fabricated by wire arc additive manufacturing

Synthesis of Functionally Graded AA7075-B4C Composite with Multi-Level Gradient Structure

Effect of Functionally Graded Material (FGM) Interlayer in Metal Additive Manufacturing of Inconel-Stainless Bimetallic Structure by Laser Melting Deposition (LMD) and Wire Arc Additive Manufacturing (WAAM)

Functionally Graded Additive Manufacturing of Thin-Walled 316L Stainless Steel-Inconel 625 by Direct Laser Metal Deposition Process: Characterization and Evaluation

Effects of ultrasonic treatment on mechanical properties and microstructure of stainless steel 308L and Inconel 718 functionally graded materials fabricated via double-wire arc additive manufacturing

Microstructure and Mechanical Properties of P21-STS316L Functionally Graded Material Manufactured by Direct Energy Deposition 3D Print

Functional grading of low alloy steel to 316 L by Wire Arc Additive Manufacturing – Microstructural and mechanical characterization of bi-metal interface