Abstract:Functionally graded materials (FGMs) are composites comprising various materials that can overcome the limitations of homogeneous materials, such as abrupt property changes at material interfaces. This results in gradual changes in the microstructure and composition, thus limiting the performance optimization under complex operating conditions. In this study, a novel ultrasonic-assisted double wire arc additive manufacturing (U-DWAAM) process is performed to fabricate stainless steel 308 L (SS 308 L) and Inconel 718 (In 718) composites with and without ultrasonic treatment. The microstructure, chemical composition, tensile strength, and hardness of the fabricated FGMs are investigated with and without ultrasonic treatment. The results show that the microstructure of the FGMs without ultrasonic treatment is mainly composed of columnar grains. However, by performing ultrasonic treatment, the grain size reduced, the homogeneity improved, and the grains refined into equiaxed grains. The chemical composition shows a smooth transition from SS 308 L to In 718, with an increase in Ni, the main element in In 718, and a decrease in Fe, the main element in SS 308 L. Typical epitaxial grain growth is observed at interfaces with different compositions. For the specimens subjected to ultrasonic treatment, their tensile strength is slightly higher and elongation lower compared with those of the specimens without ultrasonic treatment. This is attributable to the change in the equiaxed grains and a decrease in the crystal size owing to the application of ultrasound in the columnar grains. The hardness increases gradually from the SS 308 L portion of the FGMs as the mixing ratio of In 718 increases. With and without ultrasonic treatment, the percentage increase in hardness is 7%, 9%, 10%, 12%, and 15%, compared with that of the same layer without ultrasonic treatment. The increase in hardness is due to microstructural changes (equiaxed grains in the columnar phase), solid solution strengthening, and precipitation enhancement owing to an increase in Ni, Mo, and Nb contents with the In 718 content.

Investigation on dual wire TIG Arc additive manufacturing of IN625 and SS316L FGM for continuous gradient and sandwich structures

Fabrication and characterization of stainless steel 308 L / Inconel 625 functionally graded material with continuous change in composition by dual-wire arc additive manufacturing

Dual-Wire Plasma Arc Additively Manufactured SS 316L-Inconel 625 Functionally Graded Material: Microstructure Evolution and Mechanical Properties

Effect of composition gradient design on microstructure and mechanical properties of dual-wire plasma arc additively manufactured 316L/IN625 functionally graded materials

Fabrication and Fatigue Properties of Dissimilar Steel Functionally Graded Material Structure Through Wire Arc Additive Manufacturing

Characterization of Functionally Graded Material (Stainless Steel 347/308L) Fabricated through Wire and Arc Additive Manufacturing: Microstructure and Mechanical Perspectives

Investigation of Frictional Deformation on Mechanical and Metallurgical Properties of Ni-based Functionally Graded Materials Developed by Wire and Arc Additive Manufacturing

Microstructural Features and Mechanical Integrity of Wire Arc Additive Manufactured SS321/Inconel 625 Functionally Gradient Material

Deposition of Functionally Graded Material Fabricated by Robot Plasma Arc Welding

Microstructural and mechanical properties examination of SS316L-Cu functionally graded material fabricated by wire arc additive manufacturing

Study on Optimization Strategy for the Composition Transition Gradient in SS 316L/Inconel 625 Functionally Graded Materials

Research on the microstructure and mechanical properties of functional gradient materials of TC4/TC11 titanium alloys for wire arc additive manufacturing with different transitional forms

Microstructure and tribological behaviour of dissimilar steel functional structure developed via arc-based DED process

A functionally graded material from stainless steel 304 to Fe–40Al fabricated by dual wire arc additive manufacturing

Effect of in-situ cooling during pressure and frictional deformation on mechanical and metallurgical properties of Ni-based functionally graded material developed by wire arc additive manufacturing

Iron aluminide FGM thin wall fabrication using CMT-based twin wire arc additive manufacturing process

Effects of ultrasonic treatment on mechanical properties and microstructure of stainless steel 308L and Inconel 718 functionally graded materials fabricated via double-wire arc additive manufacturing

Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses

Investigations and Multi-response Optimization of Process Parameters for SS316L Cold Metal Transfer-Wire Arc Additive Manufactured Samples

Effect of synchronous electromagnetic stirring on Laves phase morphology and mechanical property of Inconel625-HSLA steel functionally graded material fabricated by wire arc additive manufacturing

Pitting corrosion studies on functionally graded Inconel 825-SS316L wall manufactured by wire arc additive manufacturing