Abstract:Functionally graded materials (FGMs) are composites comprising various materials that can overcome the limitations of homogeneous materials, such as abrupt property changes at material interfaces. This results in gradual changes in the microstructure and composition, thus limiting the performance optimization under complex operating conditions. In this study, a novel ultrasonic-assisted double wire arc additive manufacturing (U-DWAAM) process is performed to fabricate stainless steel 308 L (SS 308 L) and Inconel 718 (In 718) composites with and without ultrasonic treatment. The microstructure, chemical composition, tensile strength, and hardness of the fabricated FGMs are investigated with and without ultrasonic treatment. The results show that the microstructure of the FGMs without ultrasonic treatment is mainly composed of columnar grains. However, by performing ultrasonic treatment, the grain size reduced, the homogeneity improved, and the grains refined into equiaxed grains. The chemical composition shows a smooth transition from SS 308 L to In 718, with an increase in Ni, the main element in In 718, and a decrease in Fe, the main element in SS 308 L. Typical epitaxial grain growth is observed at interfaces with different compositions. For the specimens subjected to ultrasonic treatment, their tensile strength is slightly higher and elongation lower compared with those of the specimens without ultrasonic treatment. This is attributable to the change in the equiaxed grains and a decrease in the crystal size owing to the application of ultrasound in the columnar grains. The hardness increases gradually from the SS 308 L portion of the FGMs as the mixing ratio of In 718 increases. With and without ultrasonic treatment, the percentage increase in hardness is 7%, 9%, 10%, 12%, and 15%, compared with that of the same layer without ultrasonic treatment. The increase in hardness is due to microstructural changes (equiaxed grains in the columnar phase), solid solution strengthening, and precipitation enhancement owing to an increase in Ni, Mo, and Nb contents with the In 718 content.

Effect of in-situ cooling during pressure and frictional deformation on mechanical and metallurgical properties of Ni-based functionally graded material developed by wire arc additive manufacturing

Investigation of Frictional Deformation on Mechanical and Metallurgical Properties of Ni-based Functionally Graded Materials Developed by Wire and Arc Additive Manufacturing

A functionally graded material design from stainless steel to Ni-based superalloy by laser metal deposition coupled with thermodynamic prediction

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

Investigation on dual wire TIG Arc additive manufacturing of IN625 and SS316L FGM for continuous gradient and sandwich structures

Fabrication and characterization of stainless steel 308 L / Inconel 625 functionally graded material with continuous change in composition by dual-wire arc additive manufacturing

Additive manufacturing of a functionally graded material from Ti-6Al-4V to Invar: Experimental characterization and thermodynamic calculations

The effects and utility of homogenization and thermodynamic modeling on microstructure and mechanical properties of SS316/IN718 functionally graded materials fabricated by laser-based directed energy deposition

Preparation and investigation of microstructure and wear properties of functionally graded materials of Aluminum-Nickel alloys

Deposition of Functionally Graded Material Fabricated by Robot Plasma Arc Welding

Influence of composition gradient variation on the microstructure and mechanical properties of 316 L/Inconel718 functionally graded material fabricated by laser additive manufacturing

Effects of ultrasonic treatment on mechanical properties and microstructure of stainless steel 308L and Inconel 718 functionally graded materials fabricated via double-wire arc additive manufacturing

Effect of composition gradient design on microstructure and mechanical properties of dual-wire plasma arc additively manufactured 316L/IN625 functionally graded materials

Mechanical properties of copper-nickel functionally graded materials based on molecular dynamics simulations: material distribution and temperature effects

Study on Optimization Strategy for the Composition Transition Gradient in SS 316L/Inconel 625 Functionally Graded Materials

Local Control of Microstructure and Mechanical Properties of High-strength Steel in Electric Arc-based Additive Manufacturing

Characterization of Functionally Graded Material (Stainless Steel 347/308L) Fabricated through Wire and Arc Additive Manufacturing: Microstructure and Mechanical Perspectives

Microstructure and Mechanical Properties of P21-STS316L Functionally Graded Material Manufactured by Direct Energy Deposition 3D Print

Research on the microstructure and mechanical properties of functional gradient materials of TC4/TC11 titanium alloys for wire arc additive manufacturing with different transitional forms

Tensile behavior of stainless steel 304L to Ni-20Cr functionally graded material: experimental characterization and computational simulations

A functionally graded material from stainless steel 304 to Fe–40Al fabricated by dual wire arc additive manufacturing