Abstract:Copper (Cu)-stainless steel (SS 304L) multi-material is enduring research topic for various engineering applications such as tooling industry, aerospace, power-generation and cryogenic applications. Laser directed energy deposition (LDED) based additive manufacturing is a one of the promising technologies for fabricating Cu-SS multi-material component. However, LDED of Cu-SS is difficult due to the significant difference in thermo-physical properties and poor solubility of Cu and Fe. One of the methods to overcome this issue is adopting a functionally graded material (FGM) approach. In this pretext, the fabrication of Cu-SS FGM using the LDED process is taken up in the present study with three different Cu compositional grading approaches, such as direct (GD100Cu), 50 % (GD50Cu) and 20 % (GD20Cu). The LDED process windows for single tracks and bulk deposition of Cu-SS FGM are identified by varying the laser power, scan speed and composition of Cu and SS304L. Subsequently, the identified process window is used to deposit bulk structures of Cu-SS FGM. The LDED-built Cu-SS FGMs are characterized in terms of build quality, chemical composition, microstructural evolution and mechanical behavior. Microscopic analysis reveals, the defect-free deposition of GD100Cu and GD50Cu, at identified process parameters. For GD20Cu, the micro-crack formation in the graded region and inter-layer porosity in the Cu-rich region are two competing phenomenon, and it is observed that layer-wise increase in laser power and interlayer delay leads to minimum crack density and lower porosity. Further, increase in Cu content leads to significant change in microstructural morphology from columnar dendrites to fine cellular morphology. In Cu-SS FG structures, the chemical composition and mechanical properties are found to be changing gradually. Further, obtained ultimate tensile strength (UTS) of GD100Cu and GD50Cu is found higher than GD20Cu and the mode of failure is found to be ductile. The improved UTS in GD100Cu and GD50Cu in comparison with pure Cu arises due to formation of nano precipitate of Cu in the inter-dendritic zone of Fe rich phase. This establishes the suitability of LDED for building FG Cu-SS components at GD50Cu over GD20Cu.

Microstructure and tribological behaviour of dissimilar steel functional structure developed via arc-based DED process

Microstructural and mechanical properties examination of SS316L-Cu functionally graded material fabricated by wire arc additive manufacturing

Fabrication and Fatigue Properties of Dissimilar Steel Functionally Graded Material Structure Through Wire Arc Additive Manufacturing

Investigation on dual wire TIG Arc additive manufacturing of IN625 and SS316L FGM for continuous gradient and sandwich structures

Microstructure and Mechanical Properties of P21-STS316L Functionally Graded Material Manufactured by Direct Energy Deposition 3D Print

Characterization of Functionally Graded Material (Stainless Steel 347/308L) Fabricated through Wire and Arc Additive Manufacturing: Microstructure and Mechanical Perspectives

Spatially heterogeneous microstructure in in-situ TiO-reinforced Ti6Al4V/316L functionally graded material fabricated via directed energy deposition

Dual-Wire Plasma Arc Additively Manufactured SS 316L-Inconel 625 Functionally Graded Material: Microstructure Evolution and Mechanical Properties

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

Deposition of Functionally Graded Material Fabricated by Robot Plasma Arc Welding

Experimental study of SS316L, Inconel 625, and SS316L-IN625 functionally graded material produced by direct laser metal deposition process

Microstructural Features and Mechanical Integrity of Wire Arc Additive Manufactured SS321/Inconel 625 Functionally Gradient Material

Functional grading of low alloy steel to 316 L by Wire Arc Additive Manufacturing – Microstructural and mechanical characterization of bi-metal interface

Elucidating laser directed energy deposition based additive manufacturing of copper-stainless steel functionally graded material: Processing and material behavior

Fabrication and characterization of stainless steel 308 L / Inconel 625 functionally graded material with continuous change in composition by dual-wire arc additive manufacturing

A functionally graded material design from stainless steel to Ni-based superalloy by laser metal deposition coupled with thermodynamic prediction

A functionally graded material from stainless steel 304 to Fe–40Al fabricated by dual wire arc additive manufacturing

Investigation of Frictional Deformation on Mechanical and Metallurgical Properties of Ni-based Functionally Graded Materials Developed by Wire and Arc Additive Manufacturing

Microstructural Evolution, Mechanical and Electrochemical Performance of Duplex Stainless Steel Fabricated by Wire Arc Additive Manufacturing with ER2209 Filler Wire

Microstructure and tribological behaviour of CoCrCuFeTi high entropy alloy reinforced SS304 through friction stir processing

Analyzing microstructural evolution and wear behavior of friction stir welded dissimilar joints of SS304 and 2024-T3 Al alloy