Abstract:Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Ahead of Print. Three types of walls were produced by the direct laser metal deposition (DLMD) process; SS316L, Inconel 625 (IN625), and SS316L-Inconel 625 FGM. The thin walls were deposited on an AISI 4130 austenitic steel substrate in five layers with a length of 2 cm. The solidification behavior, secondary dendrite arm spacing (SADS) value, chemical composition, and hardness of samples were studied. Microstructures were evaluated using optical microscopy (OM) images, scanning electron microscopy (SEM), EDS Line, EDAX, and Map analyses. OM and SEM images showed an acceptable bonding between the layers in all samples. The main solidification was equiaxed dendritic and columnar dendritic in most parts. The growth of dendrites was perpendicular to the substrate. Some dendrites grew epitaxially at the interface of two sequential layers. The standard deviation of SDAS value for SS316L, IN625, and SS316L-IN625 FGM was 0.63, 0.71, and 0.73, respectively. The lowest value of SDAS was obtained in layer one, while the highest value was obtained in layer five of the thin walls. The average SDAS values for SS316L, IN625, and SS316L-IN625 FGM were 4.40, 4.53, and 4.76 μm, respectively. Therefore, the difference between the SDAS values was not significant. EDAX and Map analyses showed that the segregation of Nb and Mo to the dendritic boundary and the formation of eutectic, secondary phases, and brittle Laves phases have occurred. Additionally, the segregation of Nb and Mo to the dendritic boundary in the SS316L-IN625 FGM sample was higher than SS316L and IN625 samples. The microhardness values oscillated significantly and decreased by moving away from the substrate (in the build direction). The microhardness values of different points of the SS316L-IN625 FGM walls were in the range of 218–278 HV. EDS line scan, microstructure, and microhardness analyses indicated the successful fabrication of the SS316L-IN625 FGM by the DLMD process.

Pitting corrosion studies on functionally graded Inconel 825-SS316L wall manufactured by wire arc additive manufacturing

Characterization of Functionally Graded Material (Stainless Steel 347/308L) Fabricated through Wire and Arc Additive Manufacturing: Microstructure and Mechanical Perspectives

Microstructural Features and Mechanical Integrity of Wire Arc Additive Manufactured SS321/Inconel 625 Functionally Gradient Material

Cold Metal Transfer-Based Wire Arc Additively Manufactured Austenitic Stainless Steel/Inconel 625/Superduplex Stainless Steel Wall: Microstructural, Corrosion Properties, and Impact Toughness Evaluation

Investigation on dual wire TIG Arc additive manufacturing of IN625 and SS316L FGM for continuous gradient and sandwich structures

Microstructural and mechanical properties examination of SS316L-Cu functionally graded material fabricated by wire arc additive manufacturing

Experimental study of SS316L, Inconel 625, and SS316L-IN625 functionally graded material produced by direct laser metal deposition process

Fabrication and characterization of stainless steel 308 L / Inconel 625 functionally graded material with continuous change in composition by dual-wire arc additive manufacturing

Deposition of Functionally Graded Material Fabricated by Robot Plasma Arc Welding

Investigation of Surface Residual Stress, Mechanical Properties, and Metallurgical Characterization of Inconel 625 Multilayer Thin-Wall Component Using Cold Metal Transfer Technique

Influence of droplet transfer behaviour on the microstructure, mechanical properties and corrosion resistance of wire arc additively manufactured Inconel (IN) 625 components

Fabrication of stainless steel 308L wall through wire + arc additive manufacturing: Microstructure and numerical prediction of tensile test

Experimental study of shielding gas concentration on mechanical properties of stainless steel alloy parts using wire and arc additive manufacturing

Dual-Wire Plasma Arc Additively Manufactured SS 316L-Inconel 625 Functionally Graded Material: Microstructure Evolution and Mechanical Properties

Effect of Functionally Graded Material (FGM) Interlayer in Metal Additive Manufacturing of Inconel-Stainless Bimetallic Structure by Laser Melting Deposition (LMD) and Wire Arc Additive Manufacturing (WAAM)

Metallurgical and mechanical properties of marine grade AA5356 using wire arc additive manufacturing

Mechanical, metallurgical, and corrosion investigations on wire arc additively manufactured low carbon steel

Effect of Electromagnetic Stirring Frequency on Inconel625-High Strength Low Alloy Steel Functionally Graded Material Fabricated by Wire Arc Additive Manufacturing

Fabrication and Fatigue Properties of Dissimilar Steel Functionally Graded Material Structure Through Wire Arc Additive Manufacturing

Analyzing microstructural, residual stress, and mechanical characteristics in dissimilar welds of Inconel 59 and AISI 904L through double-pulsed gas metal arc welding

Study on Optimization Strategy for the Composition Transition Gradient in SS 316L/Inconel 625 Functionally Graded Materials