Abstract:The corrosion behavior of functionally graded cemented carbide (FGCC), with CoNiCrFe binder (WC-CoNiCrFe), has been investigated by performing electrochemical measurements and chemical characterization. The results showed that the CoNiCrFe binder was selectively dissolved in alkaline and acidic solutions. In the NaOH solution, the high contents of Ni and Co generated a passive film consisting of Co(OH) 2 , Ni(OH) 2 , Co 3 O 4 , and NiO that effectively isolated the corrosive medium from the materials. However, the contents of Fe and Cr were too low to provide satisfactory protection. In the HCl solution, the Cr element generated Cr 0 , Cr 2 O 3 , and Cr(OH) 3 . However, the Cr content was too low to form a passive film. In addition, Co, Ni and Fe in the binder were selectively dissolved in the acidic solution. Moreover, compared with the FGCC, the non-graded cemented carbide (CC) had a higher binder content and a more dispersed WC distribution. Thus, it formed a denser and thicker passive film, which was beneficial for the corrosion resistance in the NaOH solution. However, the CoNiCrFe binder was severely corroded in the HCl solution, which was due to the absence of a passive film. In comparison, the FGCC with a lower binder content and a denser WC distribution, showed a higher corrosion resistance. On the other hand, the WC grain size showed the opposite effect in alkaline and acidic solutions. In the NaOH solution, a small WC grain size increased the number of WC/CoNiCrFe interfaces, which favored the formation of a dense passive film. It, thereby reduced the probability for pitting corrosion. In the HCl solution, the corrosion generally started from grain boundaries with high interface energy as no passive film existed. Thus, a large WC grain size facilitated the improvement of the corrosion resistance. The results from the present study do not only provide a theoretical guidance for an understanding of the anticorrosion mechanism of WC-CoNiCrFe, but also a new approach for the preparation of cemented carbides with high corrosion resistance.

Characterization of a bilayer WC–Co hardmetal using Hertzian indentation technique

Characterization and forming process of a functionally graded WC-Co/Ni composite

Nano-Indentation Properties of Tungsten Carbide-Cobalt Composites as a Function of Tungsten Carbide Crystal Orientation

Fabrication and Micro-Structure of a Multilayer Functionally Graded (wc–co)–ni Composite

Investigation for the Fracture Process of WCp/Cu Functionally Graded Materials under Three-Point-Bending

Microstructures and mechanical properties of the bilayer functionally graded WC-TiC-Ni/Co cemented carbides

Microstructure and Properties of Wcp/Cu Layered Functionally Graded Materials Prepared by Vacuum Hot-Pressed Sintering

Composition design and mechanical properties of B 4 C/Al-Zn-Mg-Cu functionally graded materials prepared by laser additive manufacturing

Fabrication and Properties of Axisymmetric WC/Co Functionally Graded Hard Metal via Microwave Sintering

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Breaking the hardness–toughness trade-off in WC–Co hardmetals: Introduction of dual-scale plate-like WC and modification of prediction models

Investigation of indentation response, scratch resistance, and wear behavior of tungsten carbide coatings fabricated by two-step interstitial carburization on tungsten

Fracture behavior of cemented carbides with CoNiFe medium entropy alloy binder

Experimental investigation on the problems in the achievement of super-smooth surface of cemented carbide WC-Co through diamond turning

Fabrication of W–Cu Functionally Graded Material with Improved Mechanical Strength

A functionally graded coating from ZrN to Ti: Experimental characterization, erosion behavior and design concept

Mechanical response and grain boundary behavior of (HfNbTaTiZr)C high-entropy carbide ceramics and its constituent binary carbides

Investigation of the Machined Surface Integrity of WC-High-Entropy Alloy Cemented Carbide

Fabrication and microstructure of W/Cu functionally graded material

Corrosion behavior of functionally graded cemented carbides with CoNiCrFe binder

Faceting/Roughening of WC/Binder Interfaces in Cemented Carbides: A Review