Abstract:While the addition of WC increases the hardness and wear resistance of coatings, an excessive WC content can also induce crack initiation and propagation, increasing brittleness and leading to premature failure. Therefore, in this study, WC particles were incorporated into nickel-based coatings by plasma-arc surfacing to optimize their content and distribution, balancing their tensile properties and wear resistance. The coatings were comprehensively evaluated through microstructural analysis, hardness testing, wear resistance assessment, and tensile testing. The results show that as the mass fraction of WC increased from 45% to 65%, the increase in carbon significantly promoted the formation of M7C3, M6C, and M23C6 carbides and suppressed the formation of the γ-phase. The microstructural analysis showed that the content of massive carbides increased significantly with the increasing WC content, and the XPS analysis further confirmed that the changes in the WC and Cr7C3 phases were particularly pronounced in the high-WC coating. The 65% WC coating showed higher hardness (a 232 increase in HV1.0), a lower and more stable coefficient of friction (0.42), and better wear resistance than the 45% WC coating, with a wear rate of 3.329 × 10−6 mm3/(N·m)−1, which was 3.709 × 10−6 mm3/(N·m)−1 lower than that of the 45% WC coating. The conventional tensile test results show that the maximum stress and strain of the 45% WC coating were 71% and 36% higher than those of the 65% WC coating, respectively. In addition, the 45% WC coating exhibited better ductility and quasi-cleavage characteristics, whereas the 65% WC coating showed typical brittle cracking behavior. The results of the field tensile tests also showed that the fracture time of the 65% WC coating was 27 s shorter than that of the 45% WC coating. Overall, the 45% WC coating had a good combination of strength and toughness.

Breaking the hardness–toughness trade-off in WC–Co hardmetals: Introduction of dual-scale plate-like WC and modification of prediction models

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Achieving Combination of High Hardness and Toughness for WC-8Co Hardmetals by Creating Dual Scale Structured Plate-Like WC

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

WC-18wt.% Co with simultaneous improvements in hardness and toughness derived from nanocrystalline powder

Coarse-grained WC–6Co hardmetals with dual-scale and plate-like WC structures fabricated by convention powder metallurgy process

Design for Manufacturing of Cemented Carbide Coated Components Toward High Wear and Impact Resistance Performance

Achieving high transverse rupture strength of WC-8Co hardmetals through forming plate-like WC grains by plasma assisted milling

Properties of WC–8Co Hardmetals with Plate-Like WC Grains Prepared by Plasma-Assisted Milling

Hardness Prediction of WC-Co Cemented Carbide Based on Machine Learning Model

Enhancing Hardness and Toughness of WC Simultaneously by Dispersed ZrO2

Simultaneous Strengthening and Toughening Effects in WC–(nanoWC–Co)

Fracture Toughness of WC-Fe Cermet in W-WC-Fe Composite by Nanoindentation

Experimental investigation on the problems in the achievement of super-smooth surface of cemented carbide WC-Co through diamond turning

Microstructure, Mechanical and Tribological Properties of WC-WCoB Coating

Microstructure and Fracture Toughness of a WC-Fe Cemented Carbide Layer Produced by a Diffusion-Controlled Reaction

Microstructure and mechanical properties of WC–Co-based cemented carbide with bimodal WC grain size distribution

Establishment of a constitutive model for tungsten carbide with different cobalt content and grain size based on the split Hopkinson pressure bar impact test

Superhard bulk high-entropy carbides with enhanced toughness via metastable in-situ particles

Hardening and toughening mechanisms of cemented carbides with plate-like WC grains prepared by seeding

Optimizing Wear Resistance and Tensile Strength of Nickel-Based Coatings through Tungsten Carbide Reinforcement