Abstract:The original Johnson-Cook model's poor prediction of W90 alloy stress at high strain rate and high and low temperatures restricts research and utilization of this alloy. This study used a Split Hopkinson Pressure Bar (SHPB) device to conduct dynamic compression tests on W90 alloy over a temperature range of [-90°C,700°C] and analyze its mechanical behavior. We examined the material's different plastic phase characteristics at high and low temperatures and conducted microstructure research on impact test specimens. Then, we analyzed the stress-strain data from SHPB experiments and quasi-static compression tests on the classical Johnson-Cook model. The original Johnson-Cook model was calibrated using the stress-strain data from SHPB and quasi-static compression tests, and the modified Johnson-Cook model was established and verified. The results show that: low temperature significantly strengthens the material's stress, while increasing temperature thermal softening reduces stress; increasing strain rate increases the strain generated by the workpiece, causing faster strain hardening and thermal softening effects, resulting in higher and more stable stress; low temperature makes thicker grain boundaries, increasing plastic stress, and increasing strain rate also increases plastic stress, as well as making the material's grain boundaries thicker. The increase of strain rate makes the grain more dense, which will also show up in the increase of stress on the macroscopic level; the modified Johnson-Cook model in this paper has high agreement with experimental data, with a mean value of MAPE of only 1.85 %,which is 90.20 % lower than the traditional model, and the average value of the RMSE is 85.56 % lower than the traditional model. The modified model significantly outperforms the traditional model in predicting stress and better describes stress changes in W90 at different temperatures.

Establishment of a constitutive model for tungsten carbide with different cobalt content and grain size based on the split Hopkinson pressure bar impact test

Nano-Indentation Properties of Tungsten Carbide-Cobalt Composites as a Function of Tungsten Carbide Crystal Orientation

The Role of Material Model in the Finite Element Simulation of High-Speed Machining of Ti6Al4V

Experimental investigation on the problems in the achievement of super-smooth surface of cemented carbide WC-Co through diamond turning

Influence of cutting parameters on PCD tool wear during milling tungsten carbide

Effect of dislocation density distribution in work-hardened layer on cutting characteristics in the multi-cutting of 49Fe49Co2V alloy

A comprehensive constitutive equation for the hot deformation of WC-Co

Breaking the hardness–toughness trade-off in WC–Co hardmetals: Introduction of dual-scale plate-like WC and modification of prediction models

Mechanical characteristics of WC-Co polycrystalline under local E-beam irradiation via molecular dynamics simulations

Modification of strain rate strengthening coefficient for Johnson-Cook constitutive model of Ti6Al4V alloy

Subroutine Embedding and Finite Element Simulation of the Improved Constitutive Equation for Ti6Al4V during High-Speed Machining

A Joint Johnson-Cook-TANH Constitutive Law for Modeling Saw-Tooth Chip Formation of Ti-6AL-4V Based on an Improved Smoothed Particle Hydrodynamics Method

An improved material constitutive model for simulation of high-speed cutting of 6061-T6 aluminum alloy with high accuracy

Mechanical properties and JC constitutive modification of tungsten alloys under high strain rates and high/low temperatures

Research on the effect of cutting parameters on the machinability of polycrystalline Fe-Cr-W alloy by molecular dynamics simulation

Effect of Tungsten Carbide Additions on the Microstructure, Mechanical, and Tribological Properties of M2 High-Speed Steel Matrix Composites

Preparation, properties and microstructure of high hardness WC-co cemented carbide tool materials for ultra-precision machining

Molecular dynamics simulation of cutting mechanism of polycrystalline Fe-Cr-W alloy

Inverse determination of improved constitutive equation for cutting titanium alloy Ti-6Al-4V based on finite element analysis

Effect of particle size and high-energy ball milling time on microstructure and mechanical properties of WC-10Co cemented carbides with plate-like WC grains

A modified parallel-sided shear zone model for determining material constitutive law