Abstract:The microscopic dislocation slip and deformation of the machined surface layer of 304 stainless steel during turning leads to severe work hardening, and the study of the microstructural evolution of the surface layer of turned 304 stainless steel is of high importance to investigate microscopic plastic deformation and reduce work hardening. Most existing studies relating to the microstructural evolution of machined surfaces have used two-dimensional (2D) orthogonal cutting models. In this paper, we proposed a method to quickly build a three-dimensional (3D) bevel cutting finite element model and ABAQUS 3D cutting simulation models using temperature-displacement coupling algorithm, which can solve the problems of complex geometric modeling and low computational efficiency of ABAQUS 3D. In addition, a dislocation evolution modeling method was proposed through direct iterative optimization of intrinsic parameters, a subroutine of dislocation density evolution prediction model was written in accordance with finite element secondary development, and a joint simulation-based inverse identification method of dislocation evolution rate parameters was developed to minimize the error between simulated and experimental values of cutting forces. We compared the simulation results and the results of microstructure morphology analysis, verified the effectiveness of the inverse identification method and the dislocation density evolution prediction model, and then investigated the effect of dislocation evolution rate parameters α∗, β∗, k0 on the main cutting force, the microhardness, the dislocation density and the grain size. The microhardness changes of the cut surface were predicted using the microscopic dislocation deformation mechanism. By comparing the experimental data, we found that the predicted microhardness values of the machined surface at different cutting amounts were well consistent with the experimental data, thus verifying the credibility of the microhardness prediction model. Subsequently, the effect of cutting parameters on microhardness values, the average depth of slip zone, the equivalent plastic strain and the strain layer depth was analyzed.

Effect of dislocation density distribution in work-hardened layer on cutting characteristics in the multi-cutting of 49Fe49Co2V alloy

Investigation on the Effects of Microstructure on Machining Unidirectional Carbon Fiber Reinforced Polymer Composites with a Modified Force Model

Research on the effect of cutting parameters on the machinability of polycrystalline Fe-Cr-W alloy by molecular dynamics simulation

Molecular dynamics simulation of cutting mechanism of polycrystalline Fe-Cr-W alloy

The Role of Material Model in the Finite Element Simulation of High-Speed Machining of Ti6Al4V

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Analysis of the effect of tool geometry on the cutting process of polycrystalline Fe-Cr-W alloy based on molecular dynamics simulation

Molecular Dynamics Simulation Study on the Influence of the Abrasive Flow Process on the Cutting of Iron-Carbon Alloys (α-Fe)

Effects of Dislocation Density Evolution on Mechanical Behavior of OFHC Copper During High-Speed Machining.

Establishment of a constitutive model for tungsten carbide with different cobalt content and grain size based on the split Hopkinson pressure bar impact test

Influence of cutting parameters on PCD tool wear during milling tungsten carbide

Theoretical and numerical studies of surface microstructural transformation in ultrasonic elliptical vibration cutting tungsten heavy alloys

Effects of grain boundary and gradient structure on machining property of CoCrFeMnNi alloys

Effects of tool geometry on tungsten removal behavior during nano-cutting

Dislocation Dynamics-Based Modeling And Simulations Of Subsurface Damages Microstructure Of Orthogonal Cutting Of Titanium Alloy

Dislocation Density and Grain Size Evolution in the Machining of Al6061-T6 Alloys

Research on microhardness prediction of 304 stainless steel turning based on dislocation density

Microstructure evolution modeling of Ti6Al4V alloy during cutting using the Particle Finite Element Method and homogeneous field distributions

Multiscale Simulation of Grain Refinement Induced by Dynamic Recrystallization of Ti6Al4V Alloy During High Speed Machining

The Study on the Effect of Various Tool Wear Indicators on the Machining of MMCs

Interfacial Effects on the Dynamic Stresses in High Speed Cutting of Heterogeneous Materials