Abstract:The dense WC-M2 high-speed steel matrix composites (WC-M2 HSS MMCs) with different WC content were prepared by mechanical alloying and vacuum sintering process. Tungsten Carbide (WC) with 0, 2, 5, 8, and 10 (by weight %) were dispersed in the matrix. The effects of WC content on the densification mechanism, phase composition, microstructure, fracture morphology, and mechanical and wear properties of the sintered composites were systematically investigated. The experimental results showed that at a vacuum sintering temperature of 1260 °C, the composite material specimens achieved near-full densification, with predominant phases being Martensitic, M 7 C 3 , M 6 C, M 2 C, MC, WC, α-Fe, and γ-Fe. Reasonable WC addition has improved grain uniformity and reduced micro-defects, which enhanced the overall mechanical properties. With an increase in WC content, the hardness and relative density of the composites showed a gradual increase, whereas transverse rupture strength and impact toughness initially improved but subsequently decreased. The friction coefficient displayed an initial increase followed by a decrease, while the wear rate showed an opposite trend. The impact fracture morphology is dominated by the interfacial separation between the WC particle phase and the binder phase, supplemented by the plastic tearing of the binder phase. The impact toughness mainly depended on the fracture of the binder phase. During crack propagation, both intergranular and transgranular fractures exist, of which the intergranular fracture prevails and coarse grains are more prone to transgranular fracture. With 5 wt.% WC, the steel matrix composites obtained peak mechanical performance, with impact toughness, bending strength, and hardness measuring 13.2 J cm −2 , 1584.3 MPa, and 780.9 HV, respectively, which also yielded the highest wear resistance.

WC-Co-TiNbZr composite with simultaneously high hardness and fracture toughness

Nanostructured Diamond-Tic Composites with High Fracture Toughness

Dense Submicron-Sized ZrC – W Composite Produced by Reactive Melt in Fi Ltration at 1200 ° C

Novel TiC-based composites with enhanced mechanical properties

Novel WC-Co-Ti3SiC2 cemented carbide with ultrafine WC grains and improved mechanical properties

Microstructural evolution and toughening mechanism of WC-Co composite prepared by amorphous-crystallization method

Enhancing Hardness and Toughness of WC Simultaneously by Dispersed ZrO2

Effect of TiCp Volume Fraction and WCp Addition on the Mechanical Properties of TiCp/Cr8Mo2VSi Composites

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Study on the Microstructure and Mechanical Properties of W-wire/TiBe, ZrBe, and ZrTiBe Alloy Composites

Microstructure and Properties of ZrC–W Composite Fabricated by Reactive Infiltration of Zr2Cu into WC/W Preform

Novel Ti3SiC2-(Ti, Zr)B2 Toughened (ti, Zr)C-based Composites with Enhanced Mechanical Properties Fabricated by Dual in Situ Reactions Hot-Pressing at Low Temperature

Achieving Combination of High Hardness and Toughness for WC-8Co Hardmetals by Creating Dual Scale Structured Plate-Like WC

Toughening Cemented Carbides by Phase Transformation of Zirconia

Microstructural evolution and performance analysis of WC-11Co reinforced iron matrix composites

WC-18wt.% Co with simultaneous improvements in hardness and toughness derived from nanocrystalline powder

Effect of Tungsten Carbide Additions on the Microstructure, Mechanical, and Tribological Properties of M2 High-Speed Steel Matrix Composites

Microstructure and Mechanical Properties of Nanocrystalline Wc-Particle-Reinforced Ti-Based Composites with Nano/Ultrafine-Grained Intermetallic Matrix from Spark Plasma Sintering and Crystallization of Amorphous Phase

Fabrication and characterization of W/Cu/Ni-based high specific gravity alloy with Zr and Ti combined addition

Brazing ZrO2 Ceramic and TC4 Alloy by Novel WB Reinforced Ag-Cu Composite Filler: Microstructure and Properties

Strengthening and toughening of WC-Ni alloys by adding novel (Ti, Hf, Ta, Nb, Zr)(C, N) high entropy powder