Abstract:The corrosion behavior of functionally graded cemented carbide (FGCC), with CoNiCrFe binder (WC-CoNiCrFe), has been investigated by performing electrochemical measurements and chemical characterization. The results showed that the CoNiCrFe binder was selectively dissolved in alkaline and acidic solutions. In the NaOH solution, the high contents of Ni and Co generated a passive film consisting of Co(OH) 2 , Ni(OH) 2 , Co 3 O 4 , and NiO that effectively isolated the corrosive medium from the materials. However, the contents of Fe and Cr were too low to provide satisfactory protection. In the HCl solution, the Cr element generated Cr 0 , Cr 2 O 3 , and Cr(OH) 3 . However, the Cr content was too low to form a passive film. In addition, Co, Ni and Fe in the binder were selectively dissolved in the acidic solution. Moreover, compared with the FGCC, the non-graded cemented carbide (CC) had a higher binder content and a more dispersed WC distribution. Thus, it formed a denser and thicker passive film, which was beneficial for the corrosion resistance in the NaOH solution. However, the CoNiCrFe binder was severely corroded in the HCl solution, which was due to the absence of a passive film. In comparison, the FGCC with a lower binder content and a denser WC distribution, showed a higher corrosion resistance. On the other hand, the WC grain size showed the opposite effect in alkaline and acidic solutions. In the NaOH solution, a small WC grain size increased the number of WC/CoNiCrFe interfaces, which favored the formation of a dense passive film. It, thereby reduced the probability for pitting corrosion. In the HCl solution, the corrosion generally started from grain boundaries with high interface energy as no passive film existed. Thus, a large WC grain size facilitated the improvement of the corrosion resistance. The results from the present study do not only provide a theoretical guidance for an understanding of the anticorrosion mechanism of WC-CoNiCrFe, but also a new approach for the preparation of cemented carbides with high corrosion resistance.

Characterization and forming process of a functionally graded WC-Co/Ni composite

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Fabrication and Micro-Structure of a Multilayer Functionally Graded (wc–co)–ni Composite

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Microstructure and Properties of Wcp/Cu Layered Functionally Graded Materials Prepared by Vacuum Hot-Pressed Sintering

Characterization and stress relaxation of the functionally graded WC-Co/Ni component/stainless steel joint

Characterization of a bilayer WC–Co hardmetal using Hertzian indentation technique

Fabrication of W–Cu Functionally Graded Material with Improved Mechanical Strength

Fabrication and microstructure of W/Cu functionally graded material

Review on developments of functionally graded WC-Co via a carburizing process: Principles, insights, and industrial implications

Fabrication and Properties of Axisymmetric WC/Co Functionally Graded Hard Metal via Microwave Sintering

Microstructures and mechanical properties of the bilayer functionally graded WC-TiC-Ni/Co cemented carbides

Synthesis of Functionally Graded AA7075-B4C Composite with Multi-Level Gradient Structure

A functionally graded coating from ZrN to Ti: Experimental characterization, erosion behavior and design concept

Preparation and characterization of Al2O3–Ti3SiC2 composites and its functionally graded materials

Investigation for the Fracture Process of WCp/Cu Functionally Graded Materials under Three-Point-Bending

Corrosion behavior of functionally graded cemented carbides with CoNiCrFe binder

Oxidation behavior of functionally graded cemented carbides with CoNiFeCr multi-principal-element alloy binder

Fast fabrication of W-Cu functionally graded material by high-gravity combustion synthesis and melt-infiltration

Microstructure and mechanical properties of TiC-Ni functionally graded materials by simultaneous combustion synthesis and compaction

Fabrication of Ni/WC composite with two distinct layers through centrifugal infiltration combined with a thermite reaction