Abstract:Bi2Te3-based materials are dominating thermoelectrics for almost all of the room-temperature applications. To meet the future demands, both their thermoelectric (TE) and mechanical properties need to be further improved, which are the requisite for efficient TE modules applied in areas such as reliable micro-cooling. The conventional zone melting (ZM) and powder metallurgy (PM) methods fall short in preparing Bi2Te3-based alloys, which have both a highly textured structure for high TE properties and a fine-grained microstructure for high mechanical properties. Herein, a mechanical exfoliation combined with spark plasma sintering (ME-SPS) method is developed to prepare Bi0.5Sb1.5Te3 with highly improved mechanical properties (correlated mainly to the dislocation networks), as well as significantly improved thermoelectric properties (correlated mainly to the texture structure). In the method, both the dislocation density and the orientation factor (F) can be tuned by the sintering pressure. At a sintering pressure of 20 MPa, an exceptional F of up to 0.8 is retained, leading to an excellent power factor of 4.8 mW m-1 K-2 that is much higher than that of the PM polycrystalline. Meanwhile, the method can readily induce high-density dislocations (up to ∼1010 cm-2), improving the mechanical properties and reducing the lattice thermal conductivity as compared to the ZM ingot. In the exfoliated and then sintered (20 MPa) sample, the figure-of-merit ZT = 1.2 (at 350 K), which has increased by about ∼20%, and the compressive strength has also increased by ∼20%, compared to those of the ZM ingot, respectively. These results demonstrate that the ME-SPS method is highly effective in preparing high-performance Bi2Te3-based alloys, which are critical for TE modules in commercial applications at near-room temperature.

Mechanically Enhanced P- and N-Type Bi2Te3-based Thermoelectric Materials Reprocessed from Commercial Ingots by Ball Milling and Spark Plasma Sintering

Enhanced thermoelectric performance of n -type PbTe bulk materials fabricated by semisolid powder processing

Microstructure and thermoelectric properties of porous Bi 2 Te 2.85 Se 0.15 bulk materials fabricated by semisolid powder processing

High Thermoelectric Performance of p-Type Bi0.4Sb1.6Te3+ x Synthesized by Plasma-Assisted Ball Milling

Thermoelectric Performance Enhancement in N -Type Bi 2 (tese) 3 Alloys Owing to Nanoscale Inhomogeneity Combined with a Spark Plasma-Textured Microstructure

Cold-Sintered Bi 2 Te 3 -Based Materials for Engineering Nanograined Thermoelectrics

Enhanced Thermoelectric and Mechanical Properties in Textured N-Type Bi2te3 Prepared by Spark Plasma Sintering

Improved Thermoelectric Properties of Bi2Te3−xSexalloys by Melt Spinning and Resistance Pressing Sintering

Enhancing Thermoelectric Properties of Polycrystalline Bi 2 S 3 by Optimizing a Ball-Milling Process

Enhanced Thermoelectric and Mechanical Properties of p-type Bi0.5Sb1.5Te3 Bulk Alloys by Composite Electroless Plating with Ni&Cu

Simultaneous Enhancement of the Thermoelectric and Mechanical Performance in One-Step Sintered n-Type Bi2Te3-Based Alloys via a Facile MgB2 Doping Strategy

Enhanced Thermoelectric Performance of $p$-type BiSbTe Through Incorporation of Magnetic CrSb

Enhanced Thermoelectric Properties Obtained by Compositional Optimization in P -Type Bi X Sb 2− X Te 3 Fabricated by Mechanical Alloying and Spark Plasma Sintering

Effects of Process Parameters on Electrical Properties of N-Type Bi2Te3 Prepared by Mechanical Alloying and Spark Plasma Sintering

Enhanced thermoelectric performance in spark plasma textured bulk n-type BiTe2.7Se0.3 and p-type Bi0.5Sb1.5Te3

Enhancing the Thermoelectric and Mechanical Properties of Bi 0.5 Sb 1.5 Te 3 Modulated by the Texture and Dense Dislocation Networks

Enhanced Thermoelectric Performance of N-Type Bi2Te2.7Se0.3 Via a Simple Liquid-Assisted Shear Exfoliation

Modulation of Vacancy Defects and Texture for High Performance n‐Type Bi2Te3 via High Energy Refinement

Practical High-Performance (Bi,Sb) 2 Te 3 -Based Thermoelectric Nanocomposites Fabricated by Nanoparticle Mixing and Scrap Recycling.

Spark plasma sintered Bi-Sb-Te alloys derived from ingot scrap: Maximizing thermoelectric performance by tailoring their composition and optimizing sintering time

Enhanced Thermoelectric Performance in N-Type Bi2te2.95se0.05 Bulks Fabricated by High Pressure Sintering Technique