Abstract:Bi2Te3-based materials are dominating thermoelectrics for almost all of the room-temperature applications. To meet the future demands, both their thermoelectric (TE) and mechanical properties need to be further improved, which are the requisite for efficient TE modules applied in areas such as reliable micro-cooling. The conventional zone melting (ZM) and powder metallurgy (PM) methods fall short in preparing Bi2Te3-based alloys, which have both a highly textured structure for high TE properties and a fine-grained microstructure for high mechanical properties. Herein, a mechanical exfoliation combined with spark plasma sintering (ME-SPS) method is developed to prepare Bi0.5Sb1.5Te3 with highly improved mechanical properties (correlated mainly to the dislocation networks), as well as significantly improved thermoelectric properties (correlated mainly to the texture structure). In the method, both the dislocation density and the orientation factor (F) can be tuned by the sintering pressure. At a sintering pressure of 20 MPa, an exceptional F of up to 0.8 is retained, leading to an excellent power factor of 4.8 mW m-1 K-2 that is much higher than that of the PM polycrystalline. Meanwhile, the method can readily induce high-density dislocations (up to ∼1010 cm-2), improving the mechanical properties and reducing the lattice thermal conductivity as compared to the ZM ingot. In the exfoliated and then sintered (20 MPa) sample, the figure-of-merit ZT = 1.2 (at 350 K), which has increased by about ∼20%, and the compressive strength has also increased by ∼20%, compared to those of the ZM ingot, respectively. These results demonstrate that the ME-SPS method is highly effective in preparing high-performance Bi2Te3-based alloys, which are critical for TE modules in commercial applications at near-room temperature.

Enhanced Thermoelectric and Mechanical Properties in Textured N-Type Bi2te3 Prepared by Spark Plasma Sintering

Enhanced thermoelectric performance of n -type PbTe bulk materials fabricated by semisolid powder processing

Microstructure and thermoelectric properties of porous Bi 2 Te 2.85 Se 0.15 bulk materials fabricated by semisolid powder processing

Ultrasonic-assisted Hot Pressing of Bi2Te3-based Thermoelectric Materials

Effects of Process Parameters on Electrical Properties of N-Type Bi2Te3 Prepared by Mechanical Alloying and Spark Plasma Sintering

Improved Thermoelectric Performance of P -Type Bismuth Antimony Telluride Bulk Alloys Prepared by Hot Forging

Mechanically Enhanced P- and N-Type Bi2Te3-based Thermoelectric Materials Reprocessed from Commercial Ingots by Ball Milling and Spark Plasma Sintering

Improved Thermoelectric Properties of Bi2Te3−xSexalloys by Melt Spinning and Resistance Pressing Sintering

Thermoelectric Performance Enhancement in N -Type Bi 2 (tese) 3 Alloys Owing to Nanoscale Inhomogeneity Combined with a Spark Plasma-Textured Microstructure

Thermoelectric and Mechanical Properties of Nano-Sic-dispersed Bi2Te3 Fabricated by Mechanical Alloying and Spark Plasma Sintering

Enhanced Thermoelectric Properties Obtained by Compositional Optimization in P -Type Bi X Sb 2− X Te 3 Fabricated by Mechanical Alloying and Spark Plasma Sintering

Microstructure and Properties of P-Type (Bi0.25sb0.75)(2)te-3 Fabricated by Spark Plasma Sintering

Cold-Sintered Bi 2 Te 3 -Based Materials for Engineering Nanograined Thermoelectrics

Enhanced thermoelectric performance in spark plasma textured bulk n-type BiTe2.7Se0.3 and p-type Bi0.5Sb1.5Te3

Analysis of Thermoelectric Properties of Hot-deformed Bismuth Telluride Sintered Materials

High-performance near-room-temperature n-type Bi2Te3-based thermoelectric alloys with superior mechanical properties

Achieving High Thermoelectric Performance of n-Type Bi 2 Te 2.79 Se 0.21 Sintered Materials by Hot-Stacked Deformation

Modulation of Vacancy Defects and Texture for High Performance n‐Type Bi2Te3 via High Energy Refinement

Enhancing the Thermoelectric and Mechanical Properties of Bi 0.5 Sb 1.5 Te 3 Modulated by the Texture and Dense Dislocation Networks

Enhanced Thermoelectric and Mechanical Properties of p-type Bi0.5Sb1.5Te3 Bulk Alloys by Composite Electroless Plating with Ni&Cu

Enhanced thermoelectric properties of bismuth sulfide polycrystals prepared by mechanical alloying and spark plasma sintering