Abstract:This study presents a colloidal synthesis method to produce thermoelectric Cu3SbSe4 nanocrystals with high yield. Pb doping is employed to increase carrier concentration and effective mass, confirmed by experimental studies and theoretical calculations. Additionally, lattice distortions and other intriguing nanostructures are found to significantly reduce thermal conductivity. Consequently, the thermoelectric figure of merit zT is greatly enhanced. Developing cost‐effective and high‐performance thermoelectric (TE) materials to assemble efficient TE devices presents a multitude of challenges and opportunities. Cu3SbSe4 is a promising p‐type TE material based on relatively earth abundant elements. However, the challenge lies in its poor electrical conductivity. Herein, an efficient and scalable solution‐based approach is developed to synthesize high‐quality Cu3SbSe4 nanocrystals doped with Pb at the Sb site. After ligand displacement and annealing treatments, the dried powders are consolidated into dense pellets, and their TE properties are investigated. Pb doping effectively increases the charge carrier concentration, resulting in a significant increase in electrical conductivity, while the Seebeck coefficients remain consistently high. The calculated band structure shows that Pb doping induces band convergence, thereby increasing the effective mass. Furthermore, the large ionic radius of Pb2+ results in the generation of additional point and plane defects and interphases, dramatically enhancing phonon scattering, which significantly decreases the lattice thermal conductivity at high temperatures. Overall, a maximum figure of merit (zTmax) ≈ 0.85 at 653 K is obtained in Cu3Sb0.97Pb0.03Se4. This represents a 1.6‐fold increase compared to the undoped sample and exceeds most doped Cu3SbSe4‐based materials produced by solid‐state, demonstrating advantages of versatility and cost‐effectiveness using a solution‐based technology.

Enhanced thermoelectric performance of n -type PbTe bulk materials fabricated by semisolid powder processing

Microstructure and thermoelectric properties of porous Bi 2 Te 2.85 Se 0.15 bulk materials fabricated by semisolid powder processing

Reduced lattice thermal conductivity in nanograined Na-doped PbTe alloys by ball milling and semisolid powder processing

Achieving higher thermoelectric performance of n-type PbTe by adjusting band structure and enhanced phonons scattering

Enhanced thermoelectric performance of n-type PbTe through introducing PbSe by a fast preparation method

Thermoelectric enhancement at low temperature in nonstoichiometric lead-telluride compounds

Enhanced thermoelectric performance of PbTe based materials by Bi doping and introducing MgO nanoparticles

High Performance Thermoelectrics from Earth-Abundant Materials: Enhanced Figure of Merit in Pbs Through Nanostructuring Grain Size

Enhanced Thermoelectric Performance of N‐Type PbSe Through Semi‐Coherent Nanostructure by AgCuTe Alloying

Low Thermal Conductivity and Improved Figure of Merit in Fine-Grained Binary PbTe Thermoelectric Alloys

Band Engineering Through Pb‐Doping of Nanocrystal Building Blocks to Enhance Thermoelectric Performance in Cu3SbSe4

High-performance Ag0.8Pb18+xSbTe20 Thermoelectric Bulk Materials Fabricated by Mechanical Alloying and Spark Plasma Sintering

Enhanced Thermoelectric Performance of N-Type PbTe Through the Introduction of Low-Dimensional C60 Nanodots

Enhanced thermoelectric performance of hot-press Bi-doped n-type polycrystalline PbS

Fabrication and Property of High-Performance Ag-Pb-Sb-Te System Semiconducting Thermoelectric Materials

Achieving High-Performance N-Type PbTe Via Synergistically Optimizing Effective Mass and Carrier Concentration and Suppressing Lattice Thermal Conductivity

Dramatic Enhancement of Thermoelectric Performance in PbTe by Unconventional Grain Shrinking in Sintering Process

Nanostructures Boost the Thermoelectric Performance of PbS

Enhanced thermoelectric performance of PbTe bulk materials with figure of merit zT >2 by multi-functional alloying

Enhancing Average Zt in Pristine Pbse by Over-Stoichiometric Pb Addition

Enhancing thermoelectric properties of p-type (Bi,Sb)2Te3 via porous structures