Abstract:Traditionally, preparing p-type (Bi,Sb)(2)Te-3 based materials by the combination of ball milling and hot pressing is regarded effective to reduce the lattice thermal conductivity and obtain high zT value. However, the deteriorated electrical transport properties and poor reproducibility restrict the further promotion of such technology. In this work, we prepare Bi0.4Sb1.6Te3 materials with Te self-compensation method, which leads to a high average zT value of 1.39 from 30 to 200 degrees C with significantly enhanced reproducibility. The Te self-compensation is found to be effective in manipulating the Bi(Sb)(Te)(-) and V-Te(2+) native defects in Bi0.4Sb1.6Te3 and thus suppress the "donor-like" effect caused by ball milling. The resulting enhanced carrier concentration further brings about a convergence of multi-valley bands, which leads to an increase in the density of states (DOS) near Fermi level and delays the onset of bipolar effect, in favor of improving electrical properties meanwhile reducing the bipolar thermal conductivity. Moreover, in the melting process, the excess Te facilitates the formation of Te-rich precipitates which remain in the ball-milled powders and then volatilize during the spark plasma sintering (SPS) process, thus leaving dispersedly distributed submicron pores and concequently reduced the lattice thermal conductivity. Taken together, the peak zT value reaches 1.55 at 100 degrees C and shows excellent reproducibility in three repeated measurements, which can promote the widespread application of the ball-milled (Bi,Sb)(2)Te-3 based materials in solid-state refrigeration.

Enhanced Thermoelectric Performance of $p$-type BiSbTe Through Incorporation of Magnetic CrSb

Enhanced thermoelectric properties for p -type BiSbTe by incorporating multiferroic BiFeO 3 nanoparticles

Critical Role of Tellurium Self-Compensation in Enhancing the Thermoelectric Performance of P-Type Bi0.4Sb1.6Te3 Alloy

Enhanced Thermoelectric Properties of p-Type Bi 0.48 Sb 1.52 Te 3 /Sb 2 Te 3 Composite

Highly Enhanced Thermoelectric and Mechanical Properties of Bi-Sb-Te Compounds by Carrier Modulation and Microstructure Adjustment

Enhanced Thermoelectric Properties Obtained by Compositional Optimization in P -Type Bi X Sb 2− X Te 3 Fabricated by Mechanical Alloying and Spark Plasma Sintering

Thermoelectric performance of p-type (Bi,Sb)2Te3 incorporating amorphous Sb2S3 nanospheres

Improved Thermoelectric Performance of P-Type Bi0.5Sb1.5Te3 Through Mn Doping at Elevated Temperature

Synergistic Texturing and Bi/Sb‐Te Antisite Doping Secure High Thermoelectric Performance in Bi 0.5 Sb 1.5 Te 3 ‐Based Thin Films

Rare Earth Ytterbium Enhanced Thermoelectric Properties of P-Type Bi0.5Sb1.5Te3

Enhanced performance of Bi2Te3-based thermoelectric materials by incorporating Bi2Fe4O9 magnetic nanoparticles

Enhanced Thermoelectric and Mechanical Performances in Sintered Bi0.48Sb1.52Te3-AgSbSe2 Composite.

Unraveling electronic origins for boosting thermoelectric performance of p-type (Bi,Sb) 2 Te 3

Enhancement of thermoelectric performance in n-type PbTe1-ySey by doping Cr and tuning Te:Se ratio

High performance of Mg3Bi1.5Sb0.5 based materials for power generation: Revealing the counter-intuitive effect of tuning Bi content on the thermoelectric properties

Enhanced Thermoelectric and Mechanical Properties of p-type Bi0.5Sb1.5Te3 Bulk Alloys by Composite Electroless Plating with Ni&Cu

Enhanced thermoelectric performance at elevated temperature via suppression of intrinsic excitation in p-type Bi0.5−xSnxSb1.5Te3 thermoelectric material

Synergistic modulation of mobility and thermal conductivity in (Bi,Sb)2Te3 towards high thermoelectric performance

Microstructure and thermoelectric performance evaluation of p-type (Bi, Sb)2Te3 materials synthesized using mechanical alloying and spark plasma sintering process

Weak-ferromagnetism for room temperature thermoelectric performance enhancement in p-type (Bi,Sb)2Te3

Reduced thermal conductivity and enhanced TE performance in CrSb2via Fe-Bi co-substitution