Abstract:Bi2Te3-based materials are dominating thermoelectrics for almost all of the room-temperature applications. To meet the future demands, both their thermoelectric (TE) and mechanical properties need to be further improved, which are the requisite for efficient TE modules applied in areas such as reliable micro-cooling. The conventional zone melting (ZM) and powder metallurgy (PM) methods fall short in preparing Bi2Te3-based alloys, which have both a highly textured structure for high TE properties and a fine-grained microstructure for high mechanical properties. Herein, a mechanical exfoliation combined with spark plasma sintering (ME-SPS) method is developed to prepare Bi0.5Sb1.5Te3 with highly improved mechanical properties (correlated mainly to the dislocation networks), as well as significantly improved thermoelectric properties (correlated mainly to the texture structure). In the method, both the dislocation density and the orientation factor (F) can be tuned by the sintering pressure. At a sintering pressure of 20 MPa, an exceptional F of up to 0.8 is retained, leading to an excellent power factor of 4.8 mW m-1 K-2 that is much higher than that of the PM polycrystalline. Meanwhile, the method can readily induce high-density dislocations (up to ∼1010 cm-2), improving the mechanical properties and reducing the lattice thermal conductivity as compared to the ZM ingot. In the exfoliated and then sintered (20 MPa) sample, the figure-of-merit ZT = 1.2 (at 350 K), which has increased by about ∼20%, and the compressive strength has also increased by ∼20%, compared to those of the ZM ingot, respectively. These results demonstrate that the ME-SPS method is highly effective in preparing high-performance Bi2Te3-based alloys, which are critical for TE modules in commercial applications at near-room temperature.

Weak-ferromagnetism for room temperature thermoelectric performance enhancement in p-type (Bi,Sb)2Te3

Enhanced performance of Bi2Te3-based thermoelectric materials by incorporating Bi2Fe4O9 magnetic nanoparticles

Synergistic Texturing and Bi/Sb‐Te Antisite Doping Secure High Thermoelectric Performance in Bi 0.5 Sb 1.5 Te 3 ‐Based Thin Films

Enhanced thermoelectric properties of FeTe 2 by Sb doping prepared by solid-state reaction

Enhanced thermoelectric properties for p -type BiSbTe by incorporating multiferroic BiFeO 3 nanoparticles

Thermoelectric performance of Te composited with FeTe2 and co-doped with Sb and Se

High performance of Mg3Bi1.5Sb0.5 based materials for power generation: Revealing the counter-intuitive effect of tuning Bi content on the thermoelectric properties

Enhanced Thermoelectric Performance of $p$-type BiSbTe Through Incorporation of Magnetic CrSb

Enhanced thermoelectric performance at elevated temperature via suppression of intrinsic excitation in p-type Bi0.5−xSnxSb1.5Te3 thermoelectric material

Enhancing Thermoelectric Performance in P-Type Sb2Te3-Based Compounds Through Nb─Ag Co-Doping with Donor-Like Effect.

Isovalent co-alloying contributes to considerable improvement in thermoelectric performance of BiSe bulks with weak anisotropy

Boosting room-temperature thermoelectric performance of Mg 3 Sb 1.5 Bi 0.5 material through breaking the contradiction between carrier concentration and carrier mobility

Enhancing the Thermoelectric and Mechanical Properties of Bi 0.5 Sb 1.5 Te 3 Modulated by the Texture and Dense Dislocation Networks

Enhanced Thermoelectric Performance of Stibium and Bismuth Co-Doped SnTe Via Melt Spinning

Magnetic Iron Doping in Cu2SnS3 Ceramics for Enhanced Thermoelectric Transport Properties

Unraveling electronic origins for boosting thermoelectric performance of p-type (Bi,Sb) 2 Te 3

Enhancing Thermoelectric Performance in P‐Type Sb 2 Te 3 ‐Based Compounds Through Nb─Ag Co‐Doping with Donor‐Like Effect

Thermoelectric Cu-doped (Bi,sb)(2)te-3: Performance Enhancement and Stability Against High Electric Current Pulse

Optimized Thermoelectric Properties of Bi0.48Sb1.52Te3 Through AgCuTe Doping for Low-Grade Heat Harvesting.

Highly Enhanced Thermoelectric and Mechanical Properties of Bi-Sb-Te Compounds by Carrier Modulation and Microstructure Adjustment

Broadening the optimum thermoelectric power generation range of p-type sintered Bi0.4Sb1.6Te3 by suppressing bipolar effect