Abstract:Cu3SbSe4, featuring its earth-abundant, cheap, nontoxic and environmentally friendly constituent elements, can be considered as a promising intermediate temperature thermoelectric (TE) material. Herein, a series of p-type Bi-doped Cu3Sb1−xBixSe4 (x = 0–0.04) samples were fabricated through melting and hot pressing process, and the effects of isovalent Bi-doping on their TE properties were comparatively investigated by experimental and computational methods. TEM analysis indicates that Bi-doped samples consist of Cu3SbSe4 and Cu2−xSe impurity phases, which is in good agreement with the results of XRD, SEM and XPS. For Bi-doped samples, the reduced electrical resistivity (ρ) caused by the optimized carrier concentrations and enhanced Seebeck coefficient derived from the densities of states near the Fermi level give rise to a high power factor of ~ 1000 µWm−1 K−2 at 673 K for the Cu3Sb0.985Bi0.015Se4 sample. Additionally, the multiscale defects of Cu3SbSe4-based materials involving point defects, nanoprecipitates, amorphous phases and grain boundaries can strongly scatter phonons to depress lattice thermal conductivity (κlat), resulting in a low κlat of ~ 0.53 Wm−1 K−1 and thermal conductivity (κtot) of ~ 0.62 Wm−1 K−1 at 673 K for the Cu3Sb0.98Bi0.02Se4 sample. As a consequence, a maximum ZT value ~ 0.95 at 673 K is obtained for the Cu3Sb0.985Bi0.015Se4 sample, which is ~ 1.9 times higher than that of pristine Cu3SbSe4. This work shows that isovalent heavy element doping is an effective strategy to optimize thermoelectric properties of copper-based chalcogenides.

Isovalent co-alloying contributes to considerable improvement in thermoelectric performance of BiSe bulks with weak anisotropy

Expand band gap and suppress bipolar excitation to optimize thermoelectric performance of Bi0.35Sb1.65Te3 sintered materials

Anisotropic thermoelectric transport properties of Bi0.5Sb1.5Te2.96+x zone melted ingots

Optimizing thermoelectric properties of BiSe through Cu additive enhanced effective mass and phonon scattering

High performance and low thermal conductivity in Bi<sub>2</sub>Se<sub>3</sub> induced by the synergistic regulation of a resonant energy level and microstructure prepared by Se slow-release method

Rational triple optimizations boost near-room-temperature thermoelectric performance of BiSe

High performance of Mg3Bi1.5Sb0.5 based materials for power generation: Revealing the counter-intuitive effect of tuning Bi content on the thermoelectric properties

Achieving High Thermoelectric Performance in Bi2(Te, Se)3 Thin Film with (00 l)-Oriented by Incorporating Tellurization and Selenization Processes

Ultralow lattice thermal conductivity and enhanced power generation efficiency realized in Bi2Te2.7Se0.3/Bi2S3 nanocomposites

Intrinsically Low Thermal Conductivity In Bisbse3: A Promising Thermoelectric Material With Multiple Conduction Bands

Promoted thermoelectric performance of (Ag, Na) co-doped polycrystalline BiSe by optimizing the thermal and electrical transports simultaneously

Enhanced Thermoelectric Performance of Bi–Se Co-Doped Cu 1.8 S via Carrier Concentration Regulation and Multiscale Phonon Scattering

Improved Thermoelectric Properties of BiSbTe-AgBiSe 2 Alloys by Suppressing Bipolar Excitation

Fine-Tuning Bi2Te3-Copper Selenide Alloys Enables an Efficient n-Type Thermoelectric Conversion

Strong lattice anharmonicity securing intrinsically low lattice thermal conductivity and high performance thermoelectric SnSb2Te4 via Se alloying

BiSbTe alloy with high thermoelectric and mechanical performance for power generation

Enhanced Thermoelectric Properties of Cu3SbSe4 Compounds by Isovalent Bismuth Doping

Enhanced Thermoelectric Performance of Bi–Se Co-Doped Cu1.8S Via Carrier Concentration Regulation and Multiscale Phonon Scattering

Enhancing the Thermoelectric Performance of Bi 2 S 3 : A Promising Earth-Abundant Thermoelectric Material

High Thermoelectric Properties Realized in Earth Abundant Bi2S3 Bulk Materials Via Se and Cl Co-Doping in Solution Synthesis Process

Thermoelectric Performance of P-Type Zone-Melted Se-doped Bi 0.5 Sb 1.5 Te 3 Alloys