Abstract:Bi2Te3-based compounds are currently the most commercially relevant thermoelectric materials near room temperature. They are prepared via hot pressing, hot deformation, spark plasma sintering, and other consolidation processes, which are typically performed at 400–500 °C. Such high-temperature processes are energy-intensive and generate unnecessary waste heat, making them undesirable for a large-scale production. In this study, a low-temperature liquid-phase-assisted sintering (or so-called cold-sintering) process was employed to fabricate p-type Bi0.5Sb1.5Te3 bulk materials at temperatures below 150 °C. At the optimal sintering temperature (130 °C), a ZT value as high as 0.56 at 450 K can be achieved, competitive to that of a commercial Bi0.5Sb1.5Te3 ingot (ZT 0.8–1.0). The addition of a small amount of transient liquid facilitates grain reorientation and expedites a mass transfer process under axial compaction and liquid evaporation conditions, thus resulting in nearly fully densified Bi0.5Sb1.5Te3 pellet samples (>97% theoretical density). Furthermore, the low-temperature sintering process results in the reduction of grain size and promotes twin boundaries, resulting in a low lattice thermal conductivity of 0.57 W m–1 K–1 at 380 K due to phonon scattering. The strategy reported in this work can be used not only as a substitute for high-temperature sintering of other thermoelectric materials but also to engineer phonon scattering for high-performance thermoelectrics.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c03540.Single parabolic band model and calculated transport properties; EBSD analysis for pellet sintered at 110 °C; BSE, EDS mapping, and TEM images of pellet sintered at 130 °C; average ZT values; and XPS results (PDF)This article has not yet been cited by other publications.

Practical High-Performance (Bi,Sb) 2 Te 3 -Based Thermoelectric Nanocomposites Fabricated by Nanoparticle Mixing and Scrap Recycling.

Spark plasma sintered Bi-Sb-Te alloys derived from ingot scrap: Maximizing thermoelectric performance by tailoring their composition and optimizing sintering time

Realizing high thermoelectric performance in Te nanocomposite through Sb2Te3 incorporation

BiSbTe-based nanocomposites with high ZT: The effect of SiC nanodispersion on thermoelectric properties

(Bi,sb)2te3/sic Nanocomposites with Enhanced Thermoelectric Performance: Effect of SiC Nanoparticle Size and Compositional Modulation

Achieving High Thermoelectric Performance Through Constructing Coherent Interfaces and Building Interface Potential Barriers in N-Type Bi2Te3/Bi2Te2.7Se0.3 Nanocomposites

Nanostructuring and improved performance of ternary Bi–Sb–Te thermoelectric materials

Cold-Sintered Bi 2 Te 3 -Based Materials for Engineering Nanograined Thermoelectrics

Synthesis and Thermoelectric Properties of Bi2te3 Based Nanocomposites

Enhanced Thermoelectric Performance of Cu2Se/Bi0.4Sb1.6Te3 Nanocomposites at Elevated Temperatures

PbTe-based Thermoelectric Nanocomposites with Reduced Thermal Conductivity by SiC Nanodispersion

Synergistic Combination of Sb2Si2Te6 Additives for Enhanced Average ZT and Single-Leg Device Efficiency of Bi0.4Sb1.6Te3-based Composites

Enhanced thermoelectric and mechanical properties of Bi0.5Sb1.5Te3 alloy with dispersed yttrium oxide ceramic nanoparticles

Mechanically Enhanced P- and N-Type Bi2Te3-based Thermoelectric Materials Reprocessed from Commercial Ingots by Ball Milling and Spark Plasma Sintering

Enhanced Thermoelectric Properties of p-Type Bi 0.48 Sb 1.52 Te 3 /Sb 2 Te 3 Composite

BiSbTe alloy with high thermoelectric and mechanical performance for power generation

Enhanced Thermoelectric Properties of N-Type Bi2te3-Based Nanocomposite Fabricated by Spark Plasma Sintering

Synthesis of Nanocomposites with Improved Thermoelectric Properties

Thermoelectric Performance Enhancement in N -Type Bi 2 (tese) 3 Alloys Owing to Nanoscale Inhomogeneity Combined with a Spark Plasma-Textured Microstructure

High-Performance p-Type Bi 2 Te 3 -Based Thermoelectric Materials Enabled via Regulating Bi-Te Ratio

Lead-free AgSn4SbTe6 Nanocomposites with Enhanced Thermoelectric Properties by SiC Nanodispersion