Abstract:Fabricating chalcopyrite Cu(In,Ga)Se2 (CIGS) films from electrodeposition is one of the most effective ways to lower the production cost and energy consumption compared with that from vacuum methods. However, this process often produces a pronounced rough surface with impurity phases, induces the accumulation of gallium, and results in a low surface band gap. In this work, ammonium sulfide ((NH4)2S, AS) solution treatment is used as a single way to realize the optimization of the distribution of elements on the CIGS surface. It is revealed that this room-temperature process not only significantly reduces the surface roughness (Ra) but also incorporates sulfur (S) into the CIGS film successfully. An appropriate AS treatment duration can effectively remove the impurity phases and reduce the series resistance, and thus the dominant recombination moves from the CdS/CIGS heterojunction interface to the bulk. Consequently, the open-circuit voltage (VOC) and fill factor (FF) of solar cells have been greatly improved (from 484 to 532 mV, from 62.52 to 68.15%), leading to higher efficiency of 11.92%. This work focuses on revealing the etching mechanism of the CIGS films by the AS treatment at room temperature.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.1c00220?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.1c00220</a>.Best solar cell parameters of different unannealing samples (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.1c00220/suppl_file/ae1c00220_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Effect of Se Vapor Concentration on Cigs Film Preparation

Increasing surface band gap of Cu(In,Ga)Se2 thin films by post depositing an In-Ga-Se thin layer.

ANNEALING STUDIES ON CIGSE PREPARED BY MAGNETRON SPUTTERING

The Effects of Annealing Temperature on CIGS Solar Cells by Sputtering from Quaternary Target with Se-free Post Annealing

Investigation of Cu(In,Ga)Se2 Polycrystalline Growth: Ga Diffusion and Surface Morphology Evolution

Effects of Annealing on CuInGaSe2 Solar Cell Prepared by Magnetron Sputtering

Preparation And Characterization Of Cu(In,Ga)Se-2 Thin Films By Selenization Of Cu0.8ga0.2 And In2se3 Precursor Films

Effect of the hydrogen annealing on the properties of Mo/CuIn1-xGaxSe2/CdS solar cells junction

Se VAPOR SELENIZATION METHOD PARAMETERS FOR DEPOSITION OF CIGS FILMS (Ⅰ) INFLUENCES OF Ar FLUX ON MICROSTRUCTURE AND MORPHOLOGIES OF CIGS FILMS

Study on Two-Step Process of Preparing CIGS Films

Influences Of The Selenization Duration On Compositions And Microstructures Of Cigs Absorber

Research progress on synthesis of CuIn1-x Gax Se2 nanoparticles

Influences of Ga Concentration on Performances of CuInGaSe2 Cells Fabricated by Sputtering-Based Method with Ceramic Quaternary Target

Influences of Sulfurization on Performances of Cu(In,Ga)(Se,S)2 Cells Fabricated Based on the Method of Sputtering CIGSe Quaternary Target

Growth and Characterization of Copper Indium Gallium Diselenide Films for Solar Cells Fabrication

Synthesis and Characterization of CIGS Powder

Research progress on synthesis of CuIn 1-xGa xSe 2 nanoparticles

Gallium Diffusion in Cigs Thin Films Prepared by Sequential Sputtering/Selenization Technique

Preparation of Cu(In,Ga)Se2 Thin Film by Sputtering from Cu(In,Ga)Se2 Quaternary Target

The Effects of Selenium Content on Cu(Inga)Se-2 Thin Film Solar Cells by Sputtering from Quaternary Target with Se-Free Post Annealing

Enhancing Surface Properties for Electrodeposited Cu(In,Ga)Se 2 Films by (NH 4 ) 2 S Solution at Room Temperature