Abstract:The device performance of Cu2ZnSn(S,Se)(4) (CZTSSe) solar cells are improved significantly by annealing the full devices at 270 degrees C for 3 min in air. This paper proposes the origin of the improvement of solar cell by post annealing treatment by analyzing the results of external quantum efficiency (EQE), Raman spectra, capacitance voltage (C-V), admittance spectra (AS) measurements, and numerical simulation. The experimental results show that the dominant free hole carriers changed from deep defect Cu-zn to the much higher density of shallow defect V-cu after annealing process, which resulting the increase of density of benign [V-cu + Zn-cu] defect cluster, and the decrease of density of detrimental [2Cu(Zn) + Sn-Zn] defect cluster in the surface region of absorber. As a result, the open voltage (V-oc) and fill factor (FF) increase significantly. The short circuit current density (J(sc)) increases slightly, which can be attributed to the decrease of interface recombination as well as the improvement of band alignment at CdS/CZTSSe interface. As a consequence, the conversion efficiency of CZTSSe solar cell is improved from 4.41% to 8.02% by post-annealing the full device. Additionally, numerical simulations using wxAMPS software are conducted to reveal insight into the role of the changes of defect type, defect density, and carrier density by post-annealing treatment.

The Effects of Annealing Temperature on CIGS Solar Cells by Sputtering from Quaternary Target with Se-free Post Annealing

The effects of annealing temperature on CIGSeS solar cells by sputtering from quaternary target with H2S post annealing

Effects of Annealing on CuInGaSe2 Solar Cell Prepared by Magnetron Sputtering

Cu(In,Ga)Se-2 Solar Cells Fabricated by Sputtering from Copper-Poor and Selenium-Rich Ceramic Target with Selenium-Free Post Treatment

The Effects of Selenium Content on Cu(Inga)Se-2 Thin Film Solar Cells by Sputtering from Quaternary Target with Se-Free Post Annealing

Effect of the hydrogen annealing on the properties of Mo/CuIn1-xGaxSe2/CdS solar cells junction

Influence of Annealing Temperature on Electric Properties of CuIn1-xGaxSe2 Thin Films

Cu(In,Ga)Se-2 Thin Films Annealed with SnSe2 for Solar Cell Absorber Fabricated by Magnetron Sputtering

ANNEALING STUDIES ON CIGSE PREPARED BY MAGNETRON SPUTTERING

Influences of Ga Concentration on Performances of CuInGaSe2 Cells Fabricated by Sputtering-Based Method with Ceramic Quaternary Target

Preparation of Wide Bandgap CuGaSe2 Absorbers and Solar Cells by Sputtering a Selenium-Rich Ceramic Target and Annealing in a Selenium-Free Atmosphere

Influences of Sulfurization on Performances of Cu(In,Ga)(Se,S)2 Cells Fabricated Based on the Method of Sputtering CIGSe Quaternary Target

CIGS formation by high temperature selenization of metal precursors in H 2 Se atmosphere

Effect of Se Vapor Concentration on Cigs Film Preparation

Preparation of wide bandgap CuGaSe 2 absorbers and solar cells by sputtering a selenium-rich ceramic target and annealing in a selenium-free atmosphere

The Relationships Between Electronic Properties and Microstructure of Cu(In,Ga)Se-2 Films Prepared by Sputtering from A Quaternary Target

Characterization and performance of Cu(In,Ga)Se2 thin films incorporating low-temperature pre-annealing process

Effects of Selenium Atmosphere on Grain Growth for CZTSe Absorbers Fabricated by Selenization of As-Sputtered Precursors

The Effects of Preheating Temperature on CuInGaSe2/CdS Interface and the Device Performances

Effect of Vacuum Rapid Annealing Treatment on Performance of CIGS Solar Cells

Insight into the Role of Post-Annealing in Air for High Efficient Cu2ZnSn(S,Se)4 Solar Cells