Abstract:This paper reports an advanced deep reactive ion etching (DRIE) process for realizing ultra-deep (>500-<inline-formula> <tex-math notation="LaTeX">$\mu \text{m}$ </tex-math></inline-formula>) and ultra-high aspect-ratio (UHAR) silicon structures (AR > 40 for 1-mm through-trench etch, <inline-formula> <tex-math notation="LaTeX">$\text {AR}\approx 80$ </tex-math></inline-formula> for 500-<inline-formula> <tex-math notation="LaTeX">$\mu \text{m}$ </tex-math></inline-formula> through-trench etch, and AR > 20 for 500-<inline-formula> <tex-math notation="LaTeX">$\mu \text{m}$ </tex-math></inline-formula> through-hole etch), with straight sidewalls across a wide range of feature sizes. The challenges of making such structures are overcome by continuously ramping critical parameters of the Bosch DRIE process throughout the process, including the 380-kHz bias power during etch step, the etch/passivation step duration, and the chamber pressure. The masking material capable of enduring the long DRIE process is also discussed; 10-<inline-formula> <tex-math notation="LaTeX">$\mu \text{m}$ </tex-math></inline-formula> and 25-<inline-formula> <tex-math notation="LaTeX">$\mu \text{m}$ </tex-math></inline-formula> wide trenches are etched to a depth of >750-<inline-formula> <tex-math notation="LaTeX">$\mu \text{m}$ </tex-math></inline-formula> and >1000-<inline-formula> <tex-math notation="LaTeX">$\mu \text{m}$ </tex-math></inline-formula>, respectively, in 1-mm-thick silicon wafers with straight sidewall profiles and flat trench bottoms. Deeper trenches are expected to be etched beyond a 1-mm thick wafer with thicker and/or higher selectivity masking materials. We have also demonstrated etching of circular holes of diameters as small as 25-<inline-formula> <tex-math notation="LaTeX">$\mu \text{m}$ </tex-math></inline-formula> to a depth of >500-<inline-formula> <tex-math notation="LaTeX">$\mu \text{m}$ </tex-math></inline-formula>, and potentially with 10–15 <inline-formula> <tex-math notation="LaTeX">$\mu \text{m}$ </tex-math></inline-formula> diameter holes. This advanced DRIE process offers opportunities for applications ranging from through-silicon via in 3-D CMOS integration to emerging micro- and meso-scale microelectromechanical system applications that demand ultra-deep and UHAR DRIE. [2017–0298]

A Dual-Purpose Method to Enhance Heat Transfer and Prevent Notching Effect in Deep Reactive Ion Etching

Performance comparison of methods to evading notching effect for SOG structures in DRIE

Oxide Or Metal Interface Damage Improvement Of Deep Silicon Etch Process By Low Power Rf Of Low Frequency

Methods to Protect Silicon Microstructures from the Damages in Deep Reactive Ion Etching

Study of heat transfer on notching effect in DRIE

The Method of Prevent Footing Effect in Making SOI Micro-Mechanical Structure

A Metal-Free Additive Texturization Method Used for Diamond-Wire-sawn Multi-Crystalline Silicon Wafers

3-D finite element calculation of electric field enhancement for nanostructures fabrication mechanism on silicon surface with AFM tip induced local anodic oxidation

Dry Etching of Thick Aluminum Film for Q-improvement of Spiral Inductors on Silicon

A Novel Anisotropic Wet Etching Process of (100)-Silicon with Areaefficiency on Convex Corner Compensation Patterns

Research on Silicon Wafer Surface Phase under the Ultra-thin Slicing Process and Its Etching Hindrance Behavior during Metal-Assisted Chemical Etching

A Two-Step Etching Method to Fabricate Nanopores in Silicon

Optimization of Wet strip after Metal Hard Mask All-in-One Etch for metal void reduction and yield improvement

A Heat Conduction Structure for the Etching Process of MEMS Devices with Support Anchors

An improved method to remove anti-footing Al layer after DRIE

Effective Approaches to Improve Au Etching Process Performance in MEMS Devices

Research on Metal Protection in KOH Wet Etching Process

Bio-Inspired Hierarchical Micro-/Nanostructures for Anti-Icing Solely Fabricated by Metal-Assisted Chemical Etching.

Top Metal Layer Electro Plating Edge Bevel Removal Improvement Study

Optimization of Metal-Assisted Etchant Components for Fabrication of Porous Silicon

Ultra Deep Reactive Ion Etching of High Aspect-Ratio and Thick Silicon Using a Ramped-Parameter Process