Abstract:The etch profile control for the amorphous carbon layer (ACL) is an important step in the 3D NAND fabrication process. Because ACL is the mask material for defining the pattern of the high-aspect-ratio-contact (HARC) dielectric ONON layer etch process, precise control of its etch profile is necessary. Specifically, an ideal ACL mask profile should be free of symptoms such as hole circularity distortion, profile twisting, bowing, and undercutting. In order to achieve this desired etch performance, knowledge of various etch contributing factors must be systematically derived and applied, including etch surface chemistry, high-aspect-ratio (HAR) etchant transport, ion flux and ion energy angle distribution function (EADF) control, etc. In this work, we investigate the ACL etch fundamental characteristics through combined 2D chamber-scale plasma simulations with the hybrid plasma-equipment model (HPEM) and 3D etch profile simulations with the Monte-Carlo Feature Profile Model (MCFPM) for an inductively-coupled-plasma (ICP) reactor with RF bias at the substrate. In particular, we focus on the profile trends under different reactant fluxes and energies. Our findings indicate that maintaining a neutral-starved (ion-rich) etch regime is essential for mitigating both the channel hole etch circularity distortion and the slit etch profile twisting. To achieve this desired etch regime, the HAR ion, and neutral transport must controlled by the RF bias power and frequency, substrate temperature, etc. Furthermore, especially in this neutral-limited etch regime which is necessary for distortion and twisting mitigation, the control of the consequent aspect-ratio dependent etching (ARDE), as well as maintaining the critical dimension (CD) and reducing bowing and undercutting are also necessary. For this purpose, atomistic density functional theory (DFT) calculations have been applied to compare the reaction energetics for various ALD-like sidewall passivation chemistries. Specifically, we propose a new process based on its favorable reaction energetics. Experimental cross-section images have matched simulation results. In conclusion, our insights have provided guidance for process optimization and tool design to meet industrial demands.

A Heat Conduction Structure for the Etching Process of MEMS Devices with Support Anchors

Structural Optimization and Mechanical Simulation of MEMS Thin-Film Getter–Heater Unit

Recent Efforts in Modelling Combined Rate, Size and Thermal Effects on Single Crystal Strength

A Dual-Purpose Method to Enhance Heat Transfer and Prevent Notching Effect in Deep Reactive Ion Etching

Effective Approaches to Improve Au Etching Process Performance in MEMS Devices

(Digital Presentation) Uniformity and Profile Improvement of Fin Etching Process at Wafer Extreme Edge for Finfet Mass Production

Generalized Thermal Design Model for Comb-Capacitor Mems Devices Fabricated by Bonding-Drie Process: A Preliminary Framework

Modeling of Heat Transport and Wafer Heating Effects during Plasma Etching

Experimental Study on Evolution of Chemical Structure Defects and Secondary Contaminative Deposition during HF-Based Etching

Research on Silicon Wafer Surface Phase under the Ultra-thin Slicing Process and Its Etching Hindrance Behavior during Metal-Assisted Chemical Etching

Wafer level microarcing model in 90nm chemical-vapor deposition low-k via etch on 300mm silicon-on-insulator substrate

A New Release Process for Polysilicon Surface Micromachining Using Sacrificial Polysilicon Anchor and Photolithography after Sacrificial Etching

CMOS-Compatible Electrochemical Nanoimprint:High Throughput Fabrication of Ordered Microstructures on Semiconductor Wafer by Using a Glassy Carbon Mold

A Two-step Wet Etching Process of PZT Thin Film With Ultra-low Undercut for MEMS Applications

Investigation of the Reliability of the Interconnection between Metal Electrode and Silicon Anchor in Silicon-on-Glass Process

Surface reaction modelling of thermal atomic layer etching on blanket hafnium oxide and its application on high aspect ratio structures

The Study of Reactive Ion Etching of Heavily Doped Polysilicon Based on HBr/O2/He Plasmas for Thermopile Devices

Step Coverage and Dry Etching Process Improvement of Amorphous Carbon Hard Mask

High-aspect-ratio amorphous carbon mask etch profile control through plasma and surface chemistry optimization

Parametric Study, Modeling of Etching Process and Application for Tapered Through-Silicon-via

Hybrid electrochemical additive and subtractive manufacturing (HEASM) based on simultaneous mask electrochemical deposition and dissolution