Abstract:N-type bismuth telluride (Bi2Te3) thin films were prepared on an aluminum nitride (AlN)-coated stainless steel foil substrate to obtain optimal thermoelectric performance. The thermal co-evaporation method was adopted so that we could vary the thin film composition, enabling us to investigate the relationship between the film composition, microstructure, crystal preferred orientation and thermoelectric properties. The influence of the substrate temperature was also investigated by synthesizing two sets of thin film samples; in one set the substrate was kept at room temperature (RT) while in the other set the substrate was maintained at a high temperature, of 300 °C, during deposition. The samples deposited at RT were amorphous in the as-deposited state and therefore were annealed at 280 °C to promote crystallization and phase development. The electrical resistivity and Seebeck coefficient were measured and the results were interpreted. Both the transport properties and crystal structure were observed to be strongly affected by non-stoichiometry and the choice of substrate temperature. We observed columnar microstructures with hexagonal grains and a multi-oriented crystal structure for the thin films deposited at high substrate temperatures, whereas highly (00 l) textured thin films with columns consisting of in-plane layers were fabricated from the stoichiometric annealed thin film samples originally synthesized at RT. Special emphasis was placed on examining the nature of tellurium (Te) atom based structural defects and their influence on thin film properties. We report maximum power factor (PF) of 1.35 mW/m K2 for near-stoichiometric film deposited at high substrate temperature, which was the highest among all studied cases.

Preparation, Thermoelectric Properties and Interface Analysis of N-Type Graded Material Fesi2/Bi2te3

Preparation and interface analyses of a P-type segmented FeSi2/Bi2Te3 material

Preparation and performance of n-type FeSi2/Bi2Te3 segmented thermoelectric material

Interface Temperature Optimization and Property Description for the Thermoelectric Materials of the p-Type Graded FeSi2/Bi2Te3

Preparation and performance of P-type FeSi2/Bi2Te3 segmented thermoelectric material

Functionally Graded Electrode Materials for Thermoelectric Devices

High thermoelectric performance and anisotropy studies of n-type Mg3Bi2-based single crystal

Grain Manipulation by Annealing Treatment Realizes High-Performance N-Type Bi2Te2.4Se0.6 Thermoelectric Material and Device

Interfacial Design Contributing to High Conversion Efficiency in Mg3(Sb, Bi)2/Bi2Te3 Thermoelectric Module with Superior Stability

Realizing High-Efficiency Thermoelectric Module by Suppressing Donor-Like Effect and Improving Preferred Orientation in N-Type Bi2(Te, Se)3

Enhanced Thermoelectric Performance in N-Type Bi2Te3-Based Alloys Via Suppressing Intrinsic Excitation.

Hierarchical Low-Temperature n-Type Bi2Te3 with High Thermoelectric Performances

Fabrication, micro-structure characteristics and transport properties of co-evaporated thin films of Bi2Te3 on AlN coated stainless steel foils

Enhanced Thermoelectric and Mechanical Properties in Textured N-Type Bi2te3 Prepared by Spark Plasma Sintering

Preparation and Thermoelectric Properties of N -Type Bi 2 Te 2.7 Se 0.3 :D M

Enhanced Thermoelectric Properties of N-Type Bi2te3-Based Nanocomposite Fabricated by Spark Plasma Sintering

Na/Bi-co-doping and Heterogeneous Interfaces Leading to Enhanced Thermoelectric Performance of P-Type Mg3Sb2-based Zintls

Tunable Electrical Conductivity and Simultaneously Enhanced Thermoelectric and Mechanical Properties in n‐type Bi2Te3

Modulation of Vacancy Defects and Texture for High Performance N-Type Bi2 Te3 Via High Energy Refinement.

Thermoelectric Performance Optimization of n-Type La3−xSmxTe4/Ni Composites via Sm Doping

Maximizing the performance of n-type Mg3Bi2 based materials for room-temperature power generation and thermoelectric cooling