Abstract:Thermoelectric materials have a wide range of application because they can be directly used in refrigeration and power generation. And the Bi2Te3 stand out because of its excellent thermoelectric performance and are used in commercial thermoelectric devices. However, n-type Bi2Te3 has seriously hindered the development of Bi2Te3-based thermoelectric devices due to its weak mechanical properties and inferior thermoelectric performance. Therefore, it is urgent to develop a high-performance n-type Bi2Te3 polycrystalline. In this work, we employed interstitial Cu and the hot deformation process to optimize the thermoelectric properties of Bi2Te2.7Se0.3, and a high-performance thermoelectric module was fabricated based on this material. Our combined theoretical and experimental effort indicates that the interstitial Cu reduce the defect density in the matrix and suppresses the donor-like effect, leading to a lattice plainification effect in the material. In addition, the two-step hot deformation process significantly improves the preferred orientation of the material and boosts the mobility. As a result, a maximum ZT of 1.27 at 373 K and a remarkable high ZTave of 1.22 across the temperature range of 300−425 K are obtained. The TEG (7-pair) and TEC (127-pair) modules were fabricated with our n-type textured Cu0.01Bi2Te2.7Se0.3 coupled with commercial p-type Bi2Te3. The TEC module demonstrates superior cooling efficiency compared to the commercial Bi2Te3 device, achieving a ΔT of 65 and 83.4 K when the hot end temperature at 300 and 350 K, respectively. In addition, the TEG module attains an impressive conversion efficiency of 6.5% at a ΔT of 225 K, which is almost the highest value among the reported Bi2Te3-based TEG modules.

Functionally Graded Electrode Materials for Thermoelectric Devices

Preparation of Functionally Graded Cu/AlN/Cu Electrode Materials for Thermoelectric Devices

TiB<sub>2</sub>/AlN/Cu Functionally Graded Materials (FGMs) Fabricated by Spark Plasma Sintering (SPS) Method

TiB<sub>2</sub>/AlN/Cu Functionally Graded Materials (fgms) Fabricated by Spark Plasma Sintering (SPS) Method

TiB2/Cu Electrode Material Fabricated Via SPS

Preparation, Thermoelectric Properties and Interface Analysis of N-Type Graded Material Fesi2/Bi2te3

Joining CoSb3 to Metal Surface of FGM Electrode for Thermoelectric Modules by SPS

Microstructure of a spark-plasma-sintered Fe2VAl-type Heusler alloy for thermoelectric application

Fabrication And Evaluation Of Microscale Thermoelectric Modules Of Bi2te3-Based Alloys

Bi2Te3-Based Thermoelectric Modules for Efficient and Reliable Low-Grade Heat Recovery

Realizing High-Efficiency Thermoelectric Module by Suppressing Donor-Like Effect and Improving Preferred Orientation in N-Type Bi2(Te, Se)3

221 Fabrication and Performance Improvement of CuAlO_2 Thermoelectrics by Orientation Process and Densification

Fabrication and Performance Simulation of Microscale Thermoelectric Modules Made with Bi2Te3-Based Alloys

Structure and Property of W-Ni-Cu Functionally Graded Materials by Composite Electrodeposition

High Efficiency Bi2te3-Based Materials and Devices for Thermoelectric Power Generation Between 100 and 300 Degrees C

Sb2Te3 based alloy with high thermoelectric and mechanical performance for low-temperature energy harvesting

The Design and Progress of Thermoelectric Materials with FGM Structure

Interfacial Design Contributing to High Conversion Efficiency in Mg3(Sb, Bi)2/Bi2Te3 Thermoelectric Module with Superior Stability

Hierarchical Architectural Structures Induce High Performance in n‐Type GeTe‐Based Thermoelectrics

Microstructure Optimization of Thermoelectric τ1-Al2Fe3Si3 via Graded Temperature Heat Treatments

High efficiency Bi2Te3-based materials and devices for thermoelectric power generation between 100 and 300 °C