Abstract:Thermoelectric materials have a wide range of application because they can be directly used in refrigeration and power generation. And the Bi2Te3 stand out because of its excellent thermoelectric performance and are used in commercial thermoelectric devices. However, n-type Bi2Te3 has seriously hindered the development of Bi2Te3-based thermoelectric devices due to its weak mechanical properties and inferior thermoelectric performance. Therefore, it is urgent to develop a high-performance n-type Bi2Te3 polycrystalline. In this work, we employed interstitial Cu and the hot deformation process to optimize the thermoelectric properties of Bi2Te2.7Se0.3, and a high-performance thermoelectric module was fabricated based on this material. Our combined theoretical and experimental effort indicates that the interstitial Cu reduce the defect density in the matrix and suppresses the donor-like effect, leading to a lattice plainification effect in the material. In addition, the two-step hot deformation process significantly improves the preferred orientation of the material and boosts the mobility. As a result, a maximum ZT of 1.27 at 373 K and a remarkable high ZTave of 1.22 across the temperature range of 300−425 K are obtained. The TEG (7-pair) and TEC (127-pair) modules were fabricated with our n-type textured Cu0.01Bi2Te2.7Se0.3 coupled with commercial p-type Bi2Te3. The TEC module demonstrates superior cooling efficiency compared to the commercial Bi2Te3 device, achieving a ΔT of 65 and 83.4 K when the hot end temperature at 300 and 350 K, respectively. In addition, the TEG module attains an impressive conversion efficiency of 6.5% at a ΔT of 225 K, which is almost the highest value among the reported Bi2Te3-based TEG modules.

High Efficiency Bi2te3-Based Materials and Devices for Thermoelectric Power Generation Between 100 and 300 Degrees C

High efficiency Bi2Te3-based materials and devices for thermoelectric power generation between 100 and 300 °C

High Thermoelectric Performance of a Sc2Si2Te6 Monolayer at Medium Temperatures: an Ab Initio Study.

High‐Efficiency Thermoelectric Module Based on High‐Performance Bi0.42Sb1.58Te3 Materials

High-Performance p-Type Bi 2 Te 3 -Based Thermoelectric Materials Enabled via Regulating Bi-Te Ratio

Realizing High-Efficiency Thermoelectric Module by Suppressing Donor-Like Effect and Improving Preferred Orientation in N-Type Bi2(Te, Se)3

Bi2Te3-Based Thermoelectric Modules for Efficient and Reliable Low-Grade Heat Recovery

BiSbTe alloy with high thermoelectric and mechanical performance for power generation

Enhanced Thermoelectric Performance in N-Type Bi2Te3-Based Alloys Via Suppressing Intrinsic Excitation.

Realizing ultrahigh ZT value and efficiency of the Bi2Te3 thermoelectric module by periodic heating

High‐Performance Industrial‐Grade p‐Type (Bi,Sb)2Te3 Thermoelectric Enabled by a Stepwise Optimization Strategy

Broadening the optimum thermoelectric power generation range of p-type sintered Bi0.4Sb1.6Te3 by suppressing bipolar effect

High efficiency GeTe-based materials and modules for thermoelectric power generation

Maximizing the performance of n-type Mg3Bi2 based materials for room-temperature power generation and thermoelectric cooling

High Performance Dual-mode Module for Power Generation and Cooling Based on Optimized BiSbTe

High-Ranged <i>ZT</i> Value Promotes Thermoelectric Cooling and Power Generation in n-Type PbTe

Hierarchical Low-Temperature n-Type Bi2Te3 with High Thermoelectric Performances

Self‐Tuning N‐type Bi2(Te,Se)3/SiC Thermoelectric Nanocomposites to Realize High Performances Up to 300 °C

Sb2Te3 based alloy with high thermoelectric and mechanical performance for low-temperature energy harvesting

High Thermoelectric Performance of N-Type PbTe1−S Due to Deep Lying States Induced by Indium Doping and Spinodal Decomposition

Defect Engineering Stabilized AgSbTe2 with High Thermoelectric Performance