Abstract:In this study, we conducted research on manufacturing molybdenum (Mo) thin films by a thermal atomic layer deposition method using solid MoO2Cl2 as a precursor. Mo thin films are widely used as gate electrodes and electrodes in metal-oxide semiconductor field-effect transistors. Tungsten (W) has primarily been used as a conventional gate electrode, but it suffers from reduced resistivity due to the residual fluorine component generated from the deposition process. Thus, herein, we developed a Mo thin film with low resistivity that can substitute W. The MoO2Cl2 precursor used to deposit the Mo thin film exists in a solid state. For solid precursors, the vapor pressure does not remain constant compared to that of liquid precursors, thereby making it difficult to set process conditions. Furthermore, the use of solid precursors at temperatures 600 °C and above has many limitations. Herein, H2 was used as the reactive gas for the deposition of Mo thin films, and the deposition temperature was increased to 650 °C, which was the maximum processing temperature of the aluminum nitride heater. Additionally, deposition rate, resistivity change, and surface morphology characteristics were compared. While resistivity decreased to 12.9 μΩ∙cm with the increase of deposition temperature from 600 °C to 650 °C, surface roughness (Rq) was increased to 0.560 nm with step coverage of 97%. X-ray diffraction analysis confirmed the crystallization change in the Mo thin film with increasing process temperature, and a certain thickness of the seed layer was required for nucleation on the initial wafer of the Mo thin film. Thus, the molybdenum nitride thin film was deposited after the 4 nm deposition of Mo thin film. This study confirmed that crystallinity of Mo thin films must be increased to reduce their resistivity and that a seed layer for initial nucleation is required.

Preparation and Characterization of Molybdenum Thin Films by Direct-Current Magnetron Sputtering

Residual strain and electrical resistivity dependence of molybdenum films on DC plasma magnetron sputtering conditions

High-energy sputtering to deposit conductive and adherent single Molybdenum layer for solar cell applications

Investigation in Feasibility of Molybdenum As A Back Contact Layer for Silicon Based Quantum Dot Solar Cells

Deposition and Characterization of AZO Thin Films on Flexible Glass Substrates Using DC Magnetron Sputtering Technique

Study of molybdenum back contact layer to achieve adherent and efficient CIGS2 absorber thin-film solar cells

Electrical and Optical Properties of Molybdenum-Doped Zno Transparent Conductive Thin Films Prepared by Dc Reactive Magnetron Sputtering

The Effect of Thermal Annealing of Mo Film on the CuInSe2 Layer Texture and Device Performance

Investigation on the effect of process parameter on physical properties of RF-sputtered Mo–Ni thin films as a back contact thin-film solar cell

Preparation of Molybdenum-Doped Indium Oxide Thin Films Using Reactive Direct-Current Magnetron Sputtering

Silicon solar cell with tunneling oxide on sulfur‐deficient intrinsic MoS2 thin film

Novel Transparent Conductive ZnO∶Mo Thin Film

Growth of In2O3:Mo Thin Films by DC Reactive Magnetron Sputtering at Room Temperature

Precipitation of Molybdenum Oxides in Supersaturated Zinc Oxide Thin Films

Investigation of the Mo and MoNx Thin Films for Superconducting Electronics Application

Study on the Deposition Characteristics of Molybdenum Thin Films Deposited by the Thermal Atomic Layer Deposition Method Using MoO2Cl2 as a Precursor

Transparent conducting molybdenum-doped zinc oxide films deposited by RF magnetron sputtering

Preparation and Characteristics of MoSe2 Interlayer in Bifacial Cu(In,Ga)Se2 Solar Cells

Spatial Atomic Layer Deposition of Molybdenum Oxide for Industrial Solar Cells

Sb2Se3 thin film solar cells in substrate configuration and the back contact selenization

PREPARATION OF ZnO THIN FILM BY MAGNETRON SPUTTERING