Abstract:A MoNx coating serves as an effective wear protection layer and is crucial for the investigation of its tribological characteristics at various temperatures. This study examined the tribological characteristics of MoNx coatings that were deposited through high-power pulsed magnetron sputtering (HiPIMS) in an Ar/N2 environment with varying N2 partial pressures. The microstructures and mechanical properties of the coatings were elucidated using scanning electron microscopy, grazing-incidence-angle X-ray diffraction, energy-dispersive spectroscopy, and nanoindentation. The dry friction performances of the coatings at different heating temperatures were studied using a ball-on-disk tribometer. The MoNx coating produced by HiPIMS was composed primarily of fcc−Mo2N and featured a fine, dense column crystal with a maximum hardness of 28.8 GPa. The MoNx coatings exhibited excellent lubrication and wear reduction properties at room temperature (RT). The dry friction performances of the MoNx coatings at elevated temperatures were expected to depend on the growth of the MoO3 tribolayer. At relatively low temperatures (300 °C and 400 °C), the MoO3 tribolayer grew slowly and was not enough to provide good lubrication, causing increases in the dry friction of the coatings. However, the δ−MoN phase formed in the MoNx coating deposited at a high N2 partial pressure could facilitate the formation of MoO3 and thus decreased the friction coefficient at 400 °C. At the relatively high heating temperature of 500 °C, however, the MoO3 tribolayer grew so rapidly that the oxide layer became thick, resulting in an increase in the wear rate. It is believed that tuning the growth rate of MoO3 via optimizing the composition and structure of the MoNx coatings might be a useful way to improve the dry friction at various elevated temperatures.

Investigation of the Mo and MoNx Thin Films for Superconducting Electronics Application

Superconductivity in Two-Dimensional Η-Mo3c2 Films

Deposition and Evaluation of MoNx Films Deposited by Magnetron Sputtering

Successive layer-by-layer deposition of metal (Mo, Ag)/BN/MoS 2 nanolaminate films and the electric properties of BN/MoS 2 heterostructure on different metal substrates

Residual strain and electrical resistivity dependence of molybdenum films on DC plasma magnetron sputtering conditions

Study of DC Magnetron Sputtered Nb Films

Precipitation of Molybdenum Oxides in Supersaturated Zinc Oxide Thin Films

Preparation and Characterization of Molybdenum Thin Films by Direct-Current Magnetron Sputtering

Characterizing the Stress and Electrical Properties of Superconducting Molybdenum Films

Dry Friction Performances of MoNx Coatings Deposited by High−Power Pulsed Magnetron Sputtering

Evolutions of the Microstructure and Properties of the (CrMoNbTaZr)NX Films Prepared by Reactive Magnetron Sputtering: Effects of Stoichiometry and Crystallinity

Thermoelectric properties and electronic structure of Cr(Mo,V)Nx thin films studied by synchrotron and lab-based X-ray spectroscopy

Characterization of Superconducting Nbn, WSi and MoSi Ultra-Thin Films in Magnetic Field

Novel Transparent Conductive ZnO∶Mo Thin Film

Structural and electrical properties of fiber textured and epitaxial molybdenum thin films prepared by magnetron sputter epitaxy

MoOxthin Films Deposited by Magnetron Sputtering As an Anode for Aqueous Micro-Supercapacitors

Epitaxial Superconducting Δ-Mon Films Grown by a Chemical Solution Method.

Preparation and tribological behavior of MoSx/MoSx-Mo nanoscale multilayer films in different environments

Properties of NbxTi(1-x)N thin films deposited on 300 mm silicon wafers for upscaling superconducting digital circuits.

The Structural and Magnetic Properties For Zn1-xCoxO Thin Films

Electrical and Optical Properties of Molybdenum-Doped Zno Transparent Conductive Thin Films Prepared by Dc Reactive Magnetron Sputtering