Abstract:Films are deposited from a single Al(20)Cr(20)Mo(20)Si(21)Ti(19) alloy target in various argon/nitrogen atmospheres by direct current magnetron sputtering. Two sets of substrate parameters are examined; one with a substrate temperature of 300 K and the substrate grounded (U(0) (V,) (300 K)), and the other with the substrate biased at -50 V and its temperature maintained at 573 K (U(-50 V, 573 K)). The films produced in pure argon or at lower nitrogen flow rates are amorphous, regardless of the substrate parameters. At higher nitrogen flow rates, however, all of the coatings are found to form an FCC (face-center-cubic) NaCl-type structure. Although this coating system contains several well known immiscible nitrides, i.e. TiN, AN and Si(3)N(4), it is determined that only a single FCC phase forms, namely a single FCC (AlCrMoSiTi)N solid solution, regardless of the deposition conditions. The lower deposition rate and reduced surface roughness of the U(-50 V, 573 K) films compared to the UO V, 300 K films are considered to result from the increased densification and resputtering of coating material. The majority of the coatings are found to have hardnesses of only 10 to 16 GPa. The highest hardnesses of 25 and 22 GPa are obtained for the crystalline nitride U(-50 V, 573 K) coatings deposited at N(2)/(Ar+N(2)) ratios of 50 and 67%, respectively. More in depth explanations behind the structure and properties of these multi-element films are presented within the paper. (c) 2008 Elsevier B.V. All rights reserved.

Evolutions of the Microstructure and Properties of the (CrMoNbTaZr)NX Films Prepared by Reactive Magnetron Sputtering: Effects of Stoichiometry and Crystallinity

Structural and Mechanical Properties of Multi-Element (alcrmotatizr)nx Coatings by Reactive Magnetron Sputtering

Microstructure and mechanical properties of nano-multilayer structured (AlCrMoTaTi)Nx coatings deposited by closed field unbalanced magnetron sputtering

Structure, Composition and Mechanical Properties of Reactively Sputtered (tivcrtaw)nx High-Entropy Films

Mechanical and Tribological Properties of Laminated (NbTaMoW)Nx Films

Effects of Nitrogen Content on the Structure and Mechanical Properties of (Al0.5CrFeNiTi0.25)Nx High-Entropy Films by Reactive Sputtering

Microstructure and mechanical properties of (AlCrTiZrV)Nx high-entropy alloy nitride films by reactive magnetron sputtering

Microstructure and Mechanical Properties of Cr Films with Different Orientations Before and after Plasma Nitriding

Microstructure, mechanical properties and tribological behavior of (TiZrHfNbTa)N x high entropy films deposited by magnetron sputtering

Microstructure and properties of the AlCrMoZrTi/(AlCrMoZrTi)N multilayer high-entropy nitride ceramics films deposited by reactive RF sputtering

Deposition and Evaluation of MoNx Films Deposited by Magnetron Sputtering

Microstructure, Mechanical, and Tribological Properties of Cr-Ti-Si-N Coatings

Effects of nitrogen content on structure and mechanical properties of multi-element (AlCrNbSiTiV)N coating

Nitride Films Deposited from an Equimolar Al–Cr–Mo–Si–Ti Alloy Target by Reactive Direct Current Magnetron Sputtering

Effects of Nitrogen Flow Ratio on the Structure and Properties of Reactively Sputtered (almonbsitativzr)n(x) Coatings

Microstructure evolution and mechanical properties of refractory high-entropy alloy nitride film

Effects of nitrogen content on microstructures and mechanical properties of (AlCrTiZrHf)N high-entropy alloy nitride films

Microstructure, mechanical and tribological properties of TiCN nanocomposite films deposited by DC magnetron sputtering

The microstructure and mechanical properties of Ti(CoCr)N films produced by DC magnetron sputtering

Comparison in Mechanical and Tribological Properties of Cr–W–N and Cr–Mo–N Multilayer Films Deposited by DC Reactive Magnetron Sputtering

Microstructures and properties of (TiCrZrVAl)N high entropy ceramics films by multi-arc ion plating