Abstract:We demonstrate the fabrication of $\sim$1.08 $\mu$m deep microfluidic cavities with characteristic size as large as 7 mm $\times$ 11 mm or 11 mm diameter, using a silicon$-$glass anodic bonding technique that does not require posts to act as separators to define cavity height. Since the phase diagram of $^3$He is significantly altered under confinement, posts might act as pinning centers for phase boundaries. The previous generation of cavities relied on full wafer-bonding which is more prone to failure and requires dicing post-bonding, whereas the these cavities are made by bonding a pre-cut piece of Hoya SD-2 glass to a patterned piece of silicon in which the cavity is defined by etching. Anodic bonding was carried out at 425 $^{\circ}$C with 200 V, and we observe that pressurizing the cavity to failure ($>$ 30 bar pressure) results in glass breaking, rather than the glass-silicon bond separation. In this article, we discuss the detailed fabrication of the cavity, its edges, and details of the junction between the coin silver fill line and the silicon base of the cavity that enables a low internal-friction joint. This feature is important for mass coupling torsional oscillator experimental assays of the superfluid inertial contribution where a high quality factor ($Q$) improves frequency resolution. The surface preparation that yields well-characterized smooth surfaces to eliminate pinning sites, the use of transparent glass as a cover permitting optical access, low temperature capability and attachment of pressure-capable ports for fluid access may be features that are important in other applications.

Fabrication of Buried Microchannels with Almost Circular Cross-Section Using HNA Wet Etching

Simple and Cost-Effective Fabrication of Two-Dimensional Plastic Nanochannels from Silica Nanowire Templates

Micro Etching Method Inside Microchannels

Facile Fabrication of Helical Microfluidic Channel Based on Rope Coiling Effect

Design and fabrication of a nanofluidic channel by selective thermal oxidation and etching back of silicon dioxide made on a silicon substrate

A High-Selectivity HNA Etching System for Bulk Micromachined Deep Holes with High Roundness

Fabrication of Fluidic Chips with 1-D Nanochannels on PMMA Substrates by Photoresist-Free UV-lithography and UV-assisted Low-Temperature Bonding

Wafer-scale Fabrication of High-Aspect Ratio Nanochannels Based on Edge-Lithography Technique.

Preparation of Rhombus-Shaped Micro/nanofluidic Channels with Dimensions Ranging from Hundred Nanometers to Several Micrometers.

Fabrication of 1-d nanochannels on PMMA substrate by photoresist-free uv lithography and UV-assisted bonding under low temperature

Fabrication of the microfluidic channels in silicon wafers using isotropic wet etching method: the impact of the composition of HNA solution on etching

Laser Lithography of Monolithically‐Integrated Multi‐Level Microchannels in Silicon

Fabrication of Nanochannels with Water-Dissolvable Nanowires

Fabrication of Optofluidic Systems Using Isotropic Wet Etched Masters in < 111 > Silicon Wafer

Fabrication of full glass chips with hybrid micro- and nanochannels and their application to protein concentration

Selective etching of n-type silicon in pn junction structure in hydrofluoric acid and its application in silicon nanowire fabrication.

Fabrication of 1D nanofluidic channels on glass substrate by wet etching and room-temperature bonding

Self-Sealed Bionic Long Microchannels with Thin Walls and Designable Nanoholes Prepared by Line-Contact Capillary-Force Assembly

Fabrication of micro fluidic cavities using Si-to-glass anodic bonding

Fabrication And Characterization Of Sub-100/10nm Planar Nanofluidic Channels By Triple Thermal Oxidation And Silicon-Glass Anodic Bonding

Fabrication of angstrom-scale two-dimensional channels for mass transport