Abstract:The AlN/BN composite ceramic, fabricated via hot-press sintering, exhibits obvious anisotropy due to the establishment of directional alignment of h-BN. However, the variation and influence mechanisms of bending strength (σ) and thermal conductivity (λ) are remain unclear in different directions, which greatly limit the application of AlN/BN composite ceramics. In this paper, the effects of h-BN content on phase composition, microstructure and anisotropy of AlN/BN composite ceramics are discussed in detail. The results reveal that AlN/BN composite ceramics have three directions: perpendicular (⊥), longitudinal parallel (∥), and lateral parallel (≡) to the hot-pressing direction. The content of h-BN is a crucial factor affecting the anisotropy of AlN/BN composite ceramics. h-BN enhances the thermal conductivity in the ∥ and hinders the thermal conductivity in the ⊥. With the increase in h-BN amount, λ∥ rises gradually, while λ⊥ gradually falls. When the mass percentage of h-BN and AlN is 25 % (AB25), the λ∥ is as high as 90 W m−1 K−1, which is about 2.25 times that of λ⊥. In terms of mechanical properties, σ ≡ and σ ⊥ first increase and then decrease, while σ ∥ only decreases. This is attributable to h-BN being effective in enhancing mechanical properties by inhibiting crack propagation in the ⊥ and ≡ direction, while the promotion of crack propagation leads to a decrease in mechanical properties in the ∥ direction. σ ≡ reaches the highest values (σ ≡ = 460.2 MPa) at an h-BN amount of 10 % (AB10), which is about 1.19 and 2.04 times that of σ ⊥ and σ ∥, respectively, and 22.1 % higher than that of AB0.

Synthesis of h‐BN composite powders via aluminothermic reduction combustion route

In Situ Combustion Synthesis of TiB<sub>2</sub>-AIN Composites

High-pressure synthesis of Al<sub>2</sub>O<sub>3</sub>-cBN composites: Effect of thermodynamic condition and cBN volume fraction on their microstructure and properties

High pressure sintering behavior and mechanical properties of cBN-Ti 3Al and cBN-Ti 3Al-Al composite materials

Enhancing the thermal shock and corrosion resistance of low‐carbon Al2O3–C refractories: The role of h‐BN composite powder

Enhanced thermal shock resistance of BN-based composites sintered by hot-pressing with the introduction of nano oxides

Reactive synthesis of alumina-boron nitride composites

Synthesis of TiN–TiB2–hBN composite powders with a core-shell structure and preparation of bulk samples

Preparation and properties of sintering additive-free AlN–BN composite ceramics by hot-pressing sintering

Combustion Synthesis of Hexagonal Boron–nitride-Based Ceramics

Analysis of Mechanical Properties of Al2O3‐cBN‐hBN Composites and Identification of Main Influencing Factors

Peculiarities of γ-Al2O3 Crystallization on the Surface of h-BN Particles

Densification and comprehensive properties of h-BN-based refractories with in-situ formation of Y3Al5O12

Preparation and characterization of TiB2-Al2O3 composite powder by combustion synthesis process

Fabrication of hexagonal boron nitride based ceramics by combustion synthesis

Effect of hexagonal boron nitride content on the anisotropy of hot-press-sintered AlN/BN composite ceramics

Synthesis and characterization of cubic boron nitride (Al)-Al2O3 composites under high pressure and high temperature conditions

Microstructural evolution and mechanical properties of h-BN composite ceramics with Y2O3–AlN addition by liquid-phase sintering

EFFECT OF h-BN AS AN ADDITIVE ON PHYSICAL AND MECHANICAL PROPERTIES OF Al2TiO5 COMPOSITE

Microstructure and mechanical properties of h-BN–SiC ceramic composites prepared by in situ combustion synthesis

Microstructure and room/elevated-temperature mechanical properties of hot-pressed h-BN composite ceramics with La2O3-Al2O3-SiO2 addition