Abstract:With high activity h-BN powders as raw materials and without the using of any sintering additives, AlN–BN composite ceramics with 0–30 vol% were prepared by hot-pressing sintering in N2 at 1850 °C. Effect of h-BN content on the microstructure and properties of the composite ceramics was investigated. The results show that fully dense composite ceramics with h-BN content up to 20 vol% can be obtained and all composites show a fine-grain-microstructure with clean and clear boundaries. No “card room structure” of h-BN was formed in the samples. With the increasing h-BN content, the composites show a decreased bending strength, fracture toughness, Vickers hardness, thermal conductivity and dielectric constant. The application of high activity raw materials produces a significant grain-refinement strengthening effect and makes the composites exhibit a much higher strength and toughness compared with the results reported by other researchers. Due to the absence of sintering additive, the composite ceramics also show a quite low dielectric loss at both low and high frequency. An optimal comprehensive properties are obtained for the AlN-20 vol% BN composite: bending strength of 410 ± 21 MPa, fracture toughness of 4.21 ± 0.19 MPa·m1/2, Vickers hardness of 7.7 ± 0.2 GPa, thermal conductivity of 46.6 W·m−1·K−1, dielectric constant of 7.4 (1 MHz) and 7.48 (18 GHz), dielectric loss of 6.7 × 10−4 (1 MHz) and 6.18 × 10−3 (18 GHz).

Synthesis and characterization of cubic boron nitride (Al)-Al2O3 composites under high pressure and high temperature conditions

High pressure sintering behavior and mechanical properties of cBN-Ti 3Al and cBN-Ti 3Al-Al composite materials

High-pressure Synthesis of Al2O3-cBN Composites: Effect of Thermodynamic Condition and Cbn Volume Fraction on Their Microstructure and Properties

High-pressure Synthesis of Tungsten Carbide–cubic Boron Nitride (wc–cbn) Composites: Effect of Cbn Particle Size and Volume Fraction on Their Microstructure and Properties

High Pressure and High Temperature Sintered PcBN Using Al, B4C and C as Sintering Additive

Superhard solid solutions of diamond and cubic boron nitride

Analysis of Mechanical Properties of Al2O3‐cBN‐hBN Composites and Identification of Main Influencing Factors

Sound velocities, elasticity and thermal properties of cBN composite with AlN binder at high pressure

Enhanced thermal shock resistance of BN-based composites sintered by hot-pressing with the introduction of nano oxides

Phase composition, microstructure, and mechanical properties of PcBN composites with Ti and Ti Al binders: Effects of holding time and synthesis pressure

High Pressure Synthesis of Tungsten Carbide–Cubic Boron Nitride (WC–cBN) Composites: Effect of Thermodynamic Condition and cBN Volume Fraction on their Microstructure and Properties

In situ synthesis of PcBN composites by Sialon combined with cBN-TiB2-AlN and their properties

Effects of TiAl Alloy as a Binder on Cubic Boron Nitride Composites

Hard and tough ultrafine-grained B4C-cBN composites prepared by high-pressure sintering

High-Pressure synthesis of Al2O3-cBN-hBN Self-lubricating ceramic

Preparation of superhard cubic boron nitride sintered from commercially available submicron powders

Densification and mechanical properties of boron carbide prepared via spark plasma sintering with cubic boron nitride as an additive

Preparation and properties of sintering additive-free AlN–BN composite ceramics by hot-pressing sintering

Direct Synthesis of Sp3‐hybridized BCN Compound by High Pressure and Temperature

Self-bonding mechanism of pure polycrystalline cubic boron nitride under high pressure and temperature

Effect of Y2O3 additive on properties of PCBN composites with TiN-Ti-AlN as binder by high temperature and high pressure sintering