Abstract:The AlN/BN composite ceramic, fabricated via hot-press sintering, exhibits obvious anisotropy due to the establishment of directional alignment of h-BN. However, the variation and influence mechanisms of bending strength (σ) and thermal conductivity (λ) are remain unclear in different directions, which greatly limit the application of AlN/BN composite ceramics. In this paper, the effects of h-BN content on phase composition, microstructure and anisotropy of AlN/BN composite ceramics are discussed in detail. The results reveal that AlN/BN composite ceramics have three directions: perpendicular (⊥), longitudinal parallel (∥), and lateral parallel (≡) to the hot-pressing direction. The content of h-BN is a crucial factor affecting the anisotropy of AlN/BN composite ceramics. h-BN enhances the thermal conductivity in the ∥ and hinders the thermal conductivity in the ⊥. With the increase in h-BN amount, λ∥ rises gradually, while λ⊥ gradually falls. When the mass percentage of h-BN and AlN is 25 % (AB25), the λ∥ is as high as 90 W m−1 K−1, which is about 2.25 times that of λ⊥. In terms of mechanical properties, σ ≡ and σ ⊥ first increase and then decrease, while σ ∥ only decreases. This is attributable to h-BN being effective in enhancing mechanical properties by inhibiting crack propagation in the ⊥ and ≡ direction, while the promotion of crack propagation leads to a decrease in mechanical properties in the ∥ direction. σ ≡ reaches the highest values (σ ≡ = 460.2 MPa) at an h-BN amount of 10 % (AB10), which is about 1.19 and 2.04 times that of σ ⊥ and σ ∥, respectively, and 22.1 % higher than that of AB0.

Sound velocities, elasticity and thermal properties of cBN composite with AlN binder at high pressure

High pressure sintering behavior and mechanical properties of cBN-Ti 3Al and cBN-Ti 3Al-Al composite materials

High-pressure Synthesis of Al2O3-cBN Composites: Effect of Thermodynamic Condition and Cbn Volume Fraction on Their Microstructure and Properties

Synthesis and characterization of cubic boron nitride (Al)-Al2O3 composites under high pressure and high temperature conditions

Analysis of Mechanical Properties of Al2O3‐cBN‐hBN Composites and Identification of Main Influencing Factors

Enhanced thermal shock resistance of BN-based composites sintered by hot-pressing with the introduction of nano oxides

Effects of TiAl Alloy as a Binder on Cubic Boron Nitride Composites

Improvement in mechanical properties in AlN-h-BN composites with high thermal conductivity

High-pressure Synthesis of Tungsten Carbide–cubic Boron Nitride (wc–cbn) Composites: Effect of Cbn Particle Size and Volume Fraction on Their Microstructure and Properties

Preparation and properties of sintering additive-free AlN–BN composite ceramics by hot-pressing sintering

Phase composition, microstructure, and mechanical properties of PcBN composites with Ti and Ti Al binders: Effects of holding time and synthesis pressure

In situ synthesis of PcBN composites by Sialon combined with cBN-TiB2-AlN and their properties

Effect of hexagonal boron nitride content on the anisotropy of hot-press-sintered AlN/BN composite ceramics

High-Pressure synthesis of Al2O3-cBN-hBN Self-lubricating ceramic

Design and fabrication of graded cBN tool materials through high temperature high pressure method

High Pressure and High Temperature Sintered PcBN Using Al, B4C and C as Sintering Additive

Fabrication of machinable AlN–BN composites with high thermal conductivity by pressureless sintering turbostatic BN-coated AlN nanocomposite powders

Effect of Al Ti content on mechanical properties of in-situ synthesized PcBN composites

Experimental study on the influence of binders on plastic deformation during sintering of cubic boron nitride powder under high pressure and high temperature

Hard and tough ultrafine-grained B4C-cBN composites prepared by high-pressure sintering

Ab initio study of pressure-dependent phonon heat conduction in cubic boron nitride