Abstract:Cubic boron nitride (cBN) powders with different grain size were used as a starting material, and the pure polycrystalline cubic boron nitride (PcBN) samples were sintered under the same conditions at 7GPa, 1700 °C, 270 s. Abrasion resistance and compressive strength of sintered pure PcBN samples were tested, and the microstructure was observed and analyzed by SEM, HRTEM, XRD and Raman spectrum. The results show that the particle size of cBN has not only a great influence on microstructure and property of the sintered pure PcBN un-der the same conditions but also influence on the bonding mechanism of the cBN particles. The inner stress of the pure PcBN sintered with the cBN particle size of 10 μm during the high pressure sintering process is about 199–222% higher than that of the sample with the cBN size of 1 μm. The wear ratio and the compressive strength of PcBN samples sintered with 10 μm cBN was increased by 47.7% and 39.7% than that of the sintered sample with 1 μm cBN respectively. The coarser-grained PcBN contains serious deformation and crushing, which can be attributed to the twin boundary and the stacking faults in the samples. As a consequence, the abrasion ratio and compressive strength of the pure PcBN are dramatically increased. It is assumed that self-bonding mechanism generated from plasticity deformation, which is a main bonding mechanism for the high pressure sintering of pure cubic boron nitride.

High-pressure Synthesis of Tungsten Carbide–cubic Boron Nitride (wc–cbn) Composites: Effect of Cbn Particle Size and Volume Fraction on Their Microstructure and Properties

High Pressure Synthesis of Tungsten Carbide–Cubic Boron Nitride (WC–cBN) Composites: Effect of Thermodynamic Condition and cBN Volume Fraction on their Microstructure and Properties

High-pressure synthesis of Al<sub>2</sub>O<sub>3</sub>-cBN composites: Effect of thermodynamic condition and cBN volume fraction on their microstructure and properties

High pressure sintering behavior and mechanical properties of cBN-Ti 3Al and cBN-Ti 3Al-Al composite materials

Hard and tough ultrafine-grained B4C-cBN composites prepared by high-pressure sintering

High-pressure Preparation of Bulk Tungsten Material with Near-Full Densification and High Fracture Toughness

Compressibility And Strength Of Nanocrystalline Tungsten Boride Under Compression To 60gpa

Analysis of Mechanical Properties of Al2O3‐cBN‐hBN Composites and Identification of Main Influencing Factors

Synthesis and characterization of cubic boron nitride (Al)-Al2O3 composites under high pressure and high temperature conditions

High Pressure and High Temperature Sintered PcBN Using Al, B4C and C as Sintering Additive

In situ synthesis of PcBN composites by Sialon combined with cBN-TiB2-AlN and their properties

Densification and mechanical properties of boron carbide prepared via spark plasma sintering with cubic boron nitride as an additive

Binderless nanocrystalline tungsten carbide with enhanced hardness induced by high-pressure sintering

Phase composition, microstructure, and mechanical properties of PcBN composites with Ti and Ti Al binders: Effects of holding time and synthesis pressure

Synthesis of cBN-hBN-SiCw Nanocomposite with Superior Hardness, Strength, and Toughness

High-Pressure synthesis of Al2O3-cBN-hBN Self-lubricating ceramic

Preparation of superhard cubic boron nitride sintered from commercially available submicron powders

Self-bonding mechanism of pure polycrystalline cubic boron nitride under high pressure and temperature

A New High Pressure and High Temperature Synthesis Idea Preparation of Micron Polycrystalline Transparent Cubic Boron Nitride

Preparation And Characterization Of Polycrystalline Cubic Boron Nitride (Pcbn) Compacts By A Pressureless Sintering Process

Direct Synthesis of Sp3‐hybridized BCN Compound by High Pressure and Temperature