Abstract:The WC-Co composite material is one of the most difficult materials to manufacture using a one-step additive manufacturing process such as Laser Powder Bed Fusion process (L-PBF). Recently, the addition of hexagonal boron nitride (hBN) has conferred good mechanical properties (hardness and wear) to WC-Co. However, comprehensive studies on the feasibility of adopting L-PBF for the composite are lacking. Thus, this study seeks to use L-PBF to prepare WC-Co-hBN (hBN: 3 vol.%) cemented carbide specimens by varying the processing parameters (laser power, scan speed and scan spacing). The effects of processing parameters on microstructural and mechanical properties on specimens are investigated using microstructural and chemical composition analysis, surface porosity analysis, microhardness and fracture toughness testing. The innovation of the study is that the hBN addition coupled with the varying printing parameters can regulate the resultant microstructure of the material and dictate very different mechanical properties. In detail, the findings of the experiments indicate that scan spacing was a significant factor in obtaining high densification. A highly dense specimen at 98% relative density (12.73 g/cm 3 ) can be achieved at 0.04 mm scan spacing. We also recognized a reduction in the density generally linked to the low sinterability of BN, which resulted in a local volume increase of the specimen. Thus, hBN could be a good candidate for lightweight properties when added to materials, lowering the composite's effective density. The L-PBF procedure resulted in inhomogeneous and fast grain growth of WC, which was linked to the non-uniform temperature distribution and varying cooling rates of melt pools during processing. Processed specimens were largely composed of polyangular WC carbides and WC platelets. The volume fraction of these two structures were influenced solely by the scan speed and laser power. The WC structure type has a significant effect on the strength of the composite. As a result, the study shows possibility of fabricating cemented carbides for functionally graded applications by adjusting the process parameters affecting WC carbides' morphology.

High Pressure Synthesis of Tungsten Carbide–Cubic Boron Nitride (WC–cBN) Composites: Effect of Thermodynamic Condition and cBN Volume Fraction on their Microstructure and Properties

High-pressure Synthesis of Tungsten Carbide–cubic Boron Nitride (wc–cbn) Composites: Effect of Cbn Particle Size and Volume Fraction on Their Microstructure and Properties

High-pressure Synthesis of Al2O3-cBN Composites: Effect of Thermodynamic Condition and Cbn Volume Fraction on Their Microstructure and Properties

High pressure sintering behavior and mechanical properties of cBN-Ti 3Al and cBN-Ti 3Al-Al composite materials

Analysis of Mechanical Properties of Al2O3‐cBN‐hBN Composites and Identification of Main Influencing Factors

High-pressure Preparation of Bulk Tungsten Material with Near-Full Densification and High Fracture Toughness

Hard and tough ultrafine-grained B4C-cBN composites prepared by high-pressure sintering

Compressibility And Strength Of Nanocrystalline Tungsten Boride Under Compression To 60gpa

Synthesis and characterization of cubic boron nitride (Al)-Al2O3 composites under high pressure and high temperature conditions

High Pressure and High Temperature Sintered PcBN Using Al, B4C and C as Sintering Additive

In situ synthesis of PcBN composites by Sialon combined with cBN-TiB2-AlN and their properties

Phase composition, microstructure, and mechanical properties of PcBN composites with Ti and Ti Al binders: Effects of holding time and synthesis pressure

High-Pressure synthesis of Al2O3-cBN-hBN Self-lubricating ceramic

Binderless nanocrystalline tungsten carbide with enhanced hardness induced by high-pressure sintering

Densification and mechanical properties of boron carbide prepared via spark plasma sintering with cubic boron nitride as an additive

Microstructure and Mechanical Properties of TiN–TiB2–hBN Composites Fabricated by Reactive Hot Pressing Using TiN–B Mixture

Microstructure and Mechanical Properties of Ultrafine WC–Ni–VC–TaC–cBN Cemented Carbides Fabricated by Spark Plasma Sintering

Synthesis of cBN-hBN-SiCw Nanocomposite with Superior Hardness, Strength, and Toughness

Effect of Process Parameters on Part Quality, Microstructure, and Mechanical Properties of a WC-Co-Hexagonal Boron Nitride Alloy Prepared by Laser Power Bed Fusion Process

Preparation of superhard cubic boron nitride sintered from commercially available submicron powders

A New High Pressure and High Temperature Synthesis Idea Preparation of Micron Polycrystalline Transparent Cubic Boron Nitride