Abstract:SiC-4 vol% BN composites were hot-pressed at 2050°C for 4 h at 40 MPa in a N2 atmosphere using micron-sized β-SiC and h-BN starting powders with 1 vol% sintering additives. Four batches were prepared using four different types of additive systems, i.e. Y2O3-Sc2O3, Yb2O3-CaO, Yb2O3-MgO, and Al2O3-AlN-Y2O3. The electrical, thermal, and mechanical properties of the SiC-4 vol% BN composites, which are primarily limited by the intrinsic weakness of h-BN and by the point defects (BC and AlSi) created by the dissolution of B and Al in the SiC lattice, were successfully tuned with the use of different additive systems. The electrical conductivity of SiC-4 vol% BN composites improved ~fivefold, i.e. from 2.6 (Ω·cm)−1 for the Al2O3-AlN-Y2O3-containing specimen to 13.9 (Ω·cm)−1 for the Y2O3-Sc2O3-containing specimen, owing to grain-growth-assisted N-doping and the elimination of Al-derived acceptors. Thermal conductivity was altered by 16% with the use of different additive systems. Fracture toughness dramatically increased from 4.3 MPa∙m1/2 in Yb2O3-CaO-containing specimens to 7.3 MPa∙m1/2 in Y2O3-Sc2O3-containing specimens. The electrical conductivity, thermal conductivity, flexural strength, and fracture toughness of SiC-4 vol% BN composite sintered with 1 vol% Y2O3-Sc2O3 were 13.9 (Ω·cm)−1, 82.0 W·m−1 K−1, 505 MPa, and 7.3 MPa∙m1/2, respectively.

Preparation and properties of sintering additive-free AlN–BN composite ceramics by hot-pressing sintering

High pressure sintering behavior and mechanical properties of cBN-Ti 3Al and cBN-Ti 3Al-Al composite materials

Effect of hexagonal boron nitride content on the anisotropy of hot-press-sintered AlN/BN composite ceramics

Enhanced thermal shock resistance of BN-based composites sintered by hot-pressing with the introduction of nano oxides

Improvement in mechanical properties in AlN-h-BN composites with high thermal conductivity

High-pressure Synthesis of Al2O3-cBN Composites: Effect of Thermodynamic Condition and Cbn Volume Fraction on Their Microstructure and Properties

Microstructure and mechanical properties of AlN–hBN based machinable ceramics prepared by pressureless sintering

Fabrication of High Strength α-SiAlON/BN Composition Ceramics by Hot Pressing

Fabrication of machinable AlN–BN composites with high thermal conductivity by pressureless sintering turbostatic BN-coated AlN nanocomposite powders

Microstructure and room/elevated-temperature mechanical properties of hot-pressed h-BN composite ceramics with La2O3-Al2O3-SiO2 addition

Addition of h-BN for enhanced machinability and high mechanical strength of AlN/Mo composites

Thermal conductivity and dielectric property of hot-pressing sintered AlN–BN ceramic composites

Analysis of Mechanical Properties of Al2O3‐cBN‐hBN Composites and Identification of Main Influencing Factors

Microstructure and Mechanical Properties of TiN–TiB2–hBN Composites Fabricated by Reactive Hot Pressing Using TiN–B Mixture

Microstructural evolution of h-BN matrix composite ceramics with La-Al-Si-O glass phase during hot-pressed sintering

Microstructural evolution and mechanical properties of h-BN composite ceramics with Y2O3–AlN addition by liquid-phase sintering

Hot-pressing sintered AlN-BN ceramics with high thermal conductivity and low dielectric loss

Anisotropies in structure and properties of hot-press sintered h-BN-MAS composite ceramics: Effects of raw h-BN particle size

Tuning the electrical, thermal, and mechanical properties of SiC-BN composites using sintering additives

EFFECT OF h-BN AS AN ADDITIVE ON PHYSICAL AND MECHANICAL PROPERTIES OF Al2TiO5 COMPOSITE