Abstract:This paper investigates the behavior of transverse defects under significant total strain in conditions of complex vortex metal flow implemented through the radial shear rolling (RSR) method. The aim of this study is to assess the applicability of RSR processing for the in-depth transformation of small ingots of special steel into bars, particularly for the manufacturing of structural elements in specialized construction projects such as nuclear power plants. Although a substantial total strain is anticipated to enhance the steel structure and contribute to defect closure, the question of the development or closure of potential casting defects remains unclear. To address this issue, model tests were conducted to simulate the implementation of RSR processing. Defect behavior data under very complex vortex metal flow and high strain conditions were obtained for the first time and have scientific merit. A small steel ingot with a 32 mm diameter, containing a simulated artificial defect in the form of a transverse through-hole with a 5 mm diameter, was employed. During rolling, the workpiece diameter was progressively reduced by 2 mm with each subsequent pass, reaching a final diameter of 20 mm. Additionally, to provide a more detailed visualization of the defect evolution process, the same defect was modeled in an aluminum bar over six passes, and changes in defect volume and shape were analyzed after each pass. A highly detailed 3D visualization of the actual defect evolution was achieved based on cross-sections from experimental workpieces. These data corresponded to the total strain levels obtained by finite element method (FEM) simulation. Notably, a consistent similarity was observed between the test results for both metals, revealing a reduction in defect volume of up to 67.7%. The deformational welding of defects in the outer sections, encompassing one-third of the rod’s radius, occurred in the initial passes. However, defects in the axial zone of the rods remained unclosed, lengthening and gradually decreasing proportionally to the elongation of the rod, akin to conventional rolling. Consequently, the radial shear rolling (RSR) method is unsuitable for ingots with substantial discontinuities in the axial zone post-casting. Nevertheless, the method ensures the total welding of defects located in the outer zones of the ingots, even with minor applied deformations and a slight decrease in the diameter of the deformed ingot. Such data were obtained for the first time and should contribute to future investigations in this field.

Using the radial shear rolling method for deep development of the cast structure of ingots of special materials

Using the Radial Shear Rolling Method for Fast and Deep Processing Technology of a Steel Ingot Cast Structure

Using the Radial-Shear Rolling Method for Casted Zirconium Alloy Ingot Structure Improvement

Modeling the Evolution of Casting Defect Closure in Ingots through Radial Shear Rolling Processing

Effect of radial shear rolling on grain refinement and mechanical properties of the Al–Mg–Sc alloy

DEVELOPMENT OF THE TECHNOLOGICAL PROCESS OF ROLLING BARS IN THE NEW DESIGN RADIAL SHEAR MILL BY USING PHYSICAL MODELING

Modelling of the Rolling Process of Titanium Alloy Tube Billets in Laboratory Conditions on a RSP 14-40 Rolling Mill

Production Practice of Rolling 8mm Thickness Plate by 4300mm Heavy Plate Mill

Using of Radial-Shear Rolling to Improve the Structure and Radiation Resistance of Zirconium-Based Alloys

Effect of Radial Shear Rolling on the Structure and Mechanical Properties of a New-Generation High-Strength Aluminum Alloy Based on the Al – Zn – Mg – Ni – Fe System

Microstructure, Texture, and Deep Drawability under Two Different Cold-Rolling Processes in Ferritic Stainless Steel

Consequences of Deep Rolling at Elevated Temperature on Near-Surface and Fatigue Properties of High-Manganese TWIP Steel X40MnCrAl19-2

Asymmetric Rolling of Interstitial-Free Steel Using Differential Roll Diameters. Part I: Mechanical Properties and Deformation Textures

Development of Advanced Technologies for the Production of Innovative Materials with a Submicrocrystalline Structure by Methods of Severe Plastic Deformation

An Experimental Study of the Thermal State of a Steel Billet during Hot Rolling

Numerical simulation of cold longitudinal asymmetric rolling process

Texture and microstructure evolution during cold rolling of a strip cast and of a hot rolled austenitic stainless steel

Analysis of Temperature-Deformation Conditions for Rolling Aluminum Alloy Al–Mg–Sc Based on FEM Modeling

Formation of Microstructure and Mechanical Properties of Co-Cr-Mo Alloy by Hot Forging and Subsequent Radial Shear Rolling

Application of hollow billets for the production of railway wheels and hollow car axles by screw piercing method

Static softening behavior of 316L stainless steel under flexible rolling process