Abstract:Developing high-performance simpler alloys via simpler processing procedures is of great significance in achieving carbon dioxide emission peak and carbon neutrality. In the present study, room-temperature (RT) rolling was carried out on simple ternary Al–8Zn–1Mg alloy in order to improve its comprehensive performance by regulating microstructure evolution. Ultimate tensile strength (UTS), yield strength (YS), fracture elongation (EL%) and uniform elongation (EU%) were tested. Optical microscopy (OM), electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM) were used to characterize the microstructure evolution. Phase analysis was performed by X-ray diffraction (XRD). The results show that RT rolling significantly enhances the UTS and YS of ternary Al–8Zn–1Mg alloy, which are ∼447 MPa and ∼389 MPa, respectively, with the corresponding EL% and EU% of ∼7.1% and ∼4.1%. The comprehensive tensile properties are comparable to or even better than that of their conventional counterparts with more complex compositions or produced by more complicated techniques. Compared with the as-SS alloy, the as-SS + R alloy experiences an additional 227 MPa increase in YS. The calculated results show that fine-grain strengthening and dislocation strengthening (predominantly in the form of microbands in the present study) respectively contribute to 21 MPa and 167 MPa increases in YS. The remaining 40 MPa increase is highly likely derived from the hetero-deformation induced (HDI) strengthening of the heterostructured lamellar microbands. The delicate balance between strength and elongation is mainly attributed to the profuse microbands formed by the coupling effect of high Zn solute atoms and stress. The findings shed light on a fundamental facet of how regulating microbands can develop high performance simpler aluminum alloys which have potential applications in strength-based structural materials.

Effect of Radial Shear Rolling on the Structure and Mechanical Properties of a New-Generation High-Strength Aluminum Alloy Based on the Al – Zn – Mg – Ni – Fe System

Effect of radial shear rolling on grain refinement and mechanical properties of the Al–Mg–Sc alloy

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

A Rolled Mg‐8Al‐1Sm‐1Zn Alloy with High Strength‐Ductility via Single‐Pass Liner Rolling

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy

Influence of different rolling processes on the microstructures and mechanical properties of 6016 aluminum alloy

Microstructural Evolution and Mechanical Properties of Pure Aluminum upon Multi-Pass Caliber Rolling

Effects Of Rolling Process On Microstructure And Mechanical Property Of 7050 Aluminum Alloy

Enhancing mechanical properties and corrosion resistance of a high strength 7A99 Al alloy by introducing pre-rolling in solution and aging treatments

Using of Radial-Shear Rolling to Improve the Structure and Radiation Resistance of Zirconium-Based Alloys

Effect of asymmetric rolling and subsequent ageing on the microstructure, texture and mechanical properties of the Al-Cu-Li alloy

Significant enhancement in tensile strength of room-temperature rolled Al–8Zn–1Mg alloy induced by profuse microbands

Effect of Cryorolling and Ageing on the Microstructure and Mechanical Properties of Al 7085 Alloy

Effect of rolling deformation and passes on microstructure and mechanical properties of 7075 aluminum alloy

Effect of thermomechanical processing on mechanical properties and microstructural evolution of Al-Mg-Zn alloy

Effect of rolling on the structure and mechanical properties of the Zn-0.8Li alloy

Effect of Dual Deformation Processes on the Microstructure and Mechanical Properties of Low-Alloyed Mg-Zn-Ca-Mn Alloy

Influence of Hot Rolling on Microstructure, Corrosion and Mechanical Properties of Mg–Zn–Mn–Ca Alloy

Microstructure evolution behavior and mechanical mechanisms in a near α-Zr alloy by cold rolling

Microstructure and Microhardness Evolution of Mg-8Al-1Zn Magnesium Alloy Processed by Differential Speed Rolling at Elevated Temperatures

Effect of Warm Rolling on the Microstructure, Texture and Mechanical Properties of Extruded Mg–Zn–Ca–Ce/La Alloy