Abstract:Ultrasonic surface rolling processing (USRP) was performed on a Mg–Y–Nd–Zr alloy after equal-channel angular pressing. The result shown that the surface roughness was significantly improved, residual stress was introduced to the topmost surface, and ~450 μm gradient nanostructure (GNS) of Mg alloys was obtained after USRP treatment. The mechanism of microstructure evolution and its effect on the mechanical properties of the Mg alloy were studied in detail. There are multiple deformation mechanisms in grain refinement. In the initial stage, the coarse-grain (CG) matrix was subdivided by {10 1̅ 2} extension twins. Subsequently, the deformed grains were refined into substructures using interaction between twins, interaction between twins and dislocations, and dislocation entanglement. Moreover, the substructure contains a high density of multiple stacking faults and dislocation arrays, which can effectively block dislocation movement and promote dislocation packing. Finally, equiaxed nanograins (NGs) with high-angle grain boundaries were formed via subcrystal rotation recrystallization. With the formation of a GNS, the strength of the Mg–Y–Nd–Zr alloy considerably increased at the expense of a small amount of plasticity. The tensile test results demonstrated that the yield strength (YS) and ultimate tensile strength (UTS) of the Mg–Y–Nd–Zr alloy increased from 171.96 and 262.47 MPa to 216.06 and 330.61 MPa, respectively, and the elongation rate decreased from 20.52% to 14.65% after the USRP treatment. The YS improvement of the Mg–Y–Nd–Zr alloy after the USRP treatment was attributed to grain boundary strengthening, synergistic strengthening, dislocation strengthening, and twin strengthening. Furthermore, the microhardness of Mg–Y–Nd–Zr considerably improved after USRP treatment, and grain refinement was the primary surface strengthening mechanism of the Mg–Y – Nd – Zr alloy after the USRP treatment. The work-hardening capacity of the Mg alloy improved after the USRP treatment, and the synergistic deformation between GNS and CG matrix was the primary reason for the excellent work-hardening capacity of the Mg–Y–Nd–Zr alloy.

Effect of radial shear rolling on grain refinement and mechanical properties of the Al–Mg–Sc alloy

Effect of Radial Shear Rolling on the Structure and Mechanical Properties of a New-Generation High-Strength Aluminum Alloy Based on the Al – Zn – Mg – Ni – Fe System

Friction-mediated tuning of shear deformation and microstructure in asymmetrically rolled Mg–1Gd alloy strips

Shear Deformation and Grain Refinement in Pure Al by Asymmetric Rolling

Effect of ultrasonic surface rolling process on microstructure and properties of rolled Mg-Y-Nd-Zr alloy

Analysis of Temperature-Deformation Conditions for Rolling Aluminum Alloy Al–Mg–Sc Based on FEM Modeling

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Effect of Rolling Reduction on Microstructures and Mechanical Properties of Sc-Containing Al-3.2Cu-1.5Li Alloy

Effect of Asymmetric Rolling on the Structure and Properties of Cu-Cr-Zr Alloys

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling

Formation of Microstructure and Mechanical Properties of Co-Cr-Mo Alloy by Hot Forging and Subsequent Radial Shear Rolling

DEVELOPMENT OF THE TECHNOLOGICAL PROCESS OF ROLLING BARS IN THE NEW DESIGN RADIAL SHEAR MILL BY USING PHYSICAL MODELING

Effect of microstructure evolution on the mechanical properties of a Mg–Y–Nd–Zr alloy with a gradient nanostructure produced via ultrasonic surface rolling processing

Revealing the Microstructure Evolution Mechanism and Mechanical Responses of a Novel Al–Zn–Mg–Cu Alloy by Hot Deformation Process

Effects of Sc Addition and Rolling on the Microstructure and Mechanical Properties of Al–35Zn Alloys

Effects of Rolling Deformation on Precipitation Behavior and Mechanical Properties of Al–Zn–Mg–Cu Alloy

Influences of the Al3Sc particle content on the evolution of bimodal grain structure and mechanical properties of Al–Mg–Sc alloys processed by hard-plate rolling

Microstructure and Mechanical Properties of Rolled Mg-12gd-3y-0.4zr Alloy Sheets

Effect of Rolling Reduction on Microstructure and Mechanical Properties of Mg-9Gd-3Y-0.5Zr Alloys

Mechanical Properties and Microstructures of Ultrafine-Grained Pure Aluminum by Asymmetric Rolling