Abstract:The microstructure evolution of Mg-3Sn, Mg-3Sn-3Al-Zn (ATZ331), and Mg-3Sn-6Al-Zn (ATZ631) alloys during high-speed rolling (HSR) and annealing was studied. High-speed rolling was carried out on the three alloys at a rolling speed of 1100 m/min, a rolling temperature of 400 °C, and a reduction of 40% during a single pass. The results showed that the microstructure of the samples after HSR contained many twins and was dominated by {10−12} extension twins (ETs) and supplemented by {10−11} contraction twins (CTs) and {10−11}-{10−12} double twins (DTs). After adding Al, the content of these different types of twins was reduced. The twinning fraction decreased significantly with 3 wt% Al addition, while the twinning fraction decreased slightly with 6 wt% Al addition. The high-speed rolled alloys were annealed at 370 °C for 1 min, 2 min, 3 min, 5 min, and 8 min. When the annealing time was 1 min, the recrystallization fraction of the ATZ631 alloy was low, indicating that increasing the Al content to 6 wt% inhibited recrystallization. When the annealing time increased to 3 min, the recrystallized grains in the ATZ631 alloy grew, indicating that the grain growth progressed faster in this alloy. When the annealing time was 8 min, the grain size of the three alloys grew. The electron backscattered diffraction (EBSD) results of the alloy annealed for 8 min showed that the twin fraction in the annealed state was lower than that after high-speed rolling. In addition with the increase in Al content, the twin fraction decreased. During high-speed rolling, the maximum intensity also increased with an increase in Al content, were 22.72, 25.09, and 26.35, and the texture of the annealed alloy was weakened. The Al addition also increased the maximum intensity.

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

Dynamic recrystallization behaviors of high Mg alloyed Al-Mg alloy during high strain rate rolling deformation

Microstructures evolution, texture characteristics and mechanical properties of Mg-2.5Nd-0.5Zn-0.5Zr alloy during the high strain rate hot-rolling

Bimodal-Structured Al–Mg Alloy with High Strength and Ductility Processed by High Strain Rate Rolling at Medium Temperature

Dynamic Precipitation, Microstructure and Mechanical Properties of Mg-5Zn-1Mn Alloy Sheets Prepared by High Strain-Rate Rolling

Dynamic precipitation and twinning-induced dynamic recrystallization in Mg–6Al–3Sn–1Zn alloy during multi-pass high-speed rolling

Deformation Induced Dynamic Recrystallization and Precipitation Strengthening in an Mg-Zn-Mn Alloy Processed by High Strain Rate Rolling

Microstructure Evolution and Mechanical Properties of Mg-3al-3sn-1zn Alloy During Multi-Pass High-Speed Rolling

Effect of Al addition and rolling reduction on microstructure and texture evolution of Mg–3Sn alloy during high-speed rolling

High Strength and Large Ductility of a Fine-Grained Al–Mg Alloy Processed by High Strain Rate Hot Rolling and Cold Rolling

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy

Enhancing the Mechanical Properties of High Strain Rate Rolled Mg–6Zn–1Mn Alloy by Pre-Rolling

Non-basal Slips Mediated Dynamic Recrystallization Promote Synergistic Strengthening and Toughening of Centrifugal Casting Mg–1.1Mn–0.5Al Alloy via High Strain Rolling

Enhancing Damping Capacity and Mechanical Properties of Al-Mg Alloy by High Strain Rate Hot Rolling and Subsequent Cold Rolling

Microstructure Evolution and Mechanical Properties of High-Strength Mg-Gd-Y-Zn-Mn Alloy Processed by Asymmetric Hot Rolling

Microstructure and texture evolution during high-strain-rate superplastic deformation of coarse-grained Mg-Gd-Y-Zr rolled sheet

Effect of Al addition and annealing on the microstructure evolution of Mg-3Sn Mg alloy subjected to high-speed rolling

Microstructure and Microhardness Evolution of Mg-8Al-1Zn Magnesium Alloy Processed by Differential Speed Rolling at Elevated Temperatures

Dynamic recrystallization behavior and mechanical properties response of rheo-extruded Al–Mg alloys with various Mg contents

Rolling Temperature and Subsequent Annealing on Microstructure, Texture and Mechanical Properties of Consecutive Rolled Mg-2.0zn-0.8gd Alloy

Effect of Rolling with Different Amounts of Deformation on Microstructure and Mechanical Properties of the Mg–1Al–4Y Alloy