Abstract:This paper investigates the behavior of transverse defects under significant total strain in conditions of complex vortex metal flow implemented through the radial shear rolling (RSR) method. The aim of this study is to assess the applicability of RSR processing for the in-depth transformation of small ingots of special steel into bars, particularly for the manufacturing of structural elements in specialized construction projects such as nuclear power plants. Although a substantial total strain is anticipated to enhance the steel structure and contribute to defect closure, the question of the development or closure of potential casting defects remains unclear. To address this issue, model tests were conducted to simulate the implementation of RSR processing. Defect behavior data under very complex vortex metal flow and high strain conditions were obtained for the first time and have scientific merit. A small steel ingot with a 32 mm diameter, containing a simulated artificial defect in the form of a transverse through-hole with a 5 mm diameter, was employed. During rolling, the workpiece diameter was progressively reduced by 2 mm with each subsequent pass, reaching a final diameter of 20 mm. Additionally, to provide a more detailed visualization of the defect evolution process, the same defect was modeled in an aluminum bar over six passes, and changes in defect volume and shape were analyzed after each pass. A highly detailed 3D visualization of the actual defect evolution was achieved based on cross-sections from experimental workpieces. These data corresponded to the total strain levels obtained by finite element method (FEM) simulation. Notably, a consistent similarity was observed between the test results for both metals, revealing a reduction in defect volume of up to 67.7%. The deformational welding of defects in the outer sections, encompassing one-third of the rod’s radius, occurred in the initial passes. However, defects in the axial zone of the rods remained unclosed, lengthening and gradually decreasing proportionally to the elongation of the rod, akin to conventional rolling. Consequently, the radial shear rolling (RSR) method is unsuitable for ingots with substantial discontinuities in the axial zone post-casting. Nevertheless, the method ensures the total welding of defects located in the outer zones of the ingots, even with minor applied deformations and a slight decrease in the diameter of the deformed ingot. Such data were obtained for the first time and should contribute to future investigations in this field.

DEVELOPMENT OF THE TECHNOLOGICAL PROCESS OF ROLLING BARS IN THE NEW DESIGN RADIAL SHEAR MILL BY USING PHYSICAL MODELING

Modeling Microstructure Evolution in Shape Memory Alloy Rods Via Legendre Wavelets Collocation Method

Analysis of Temperature-Deformation Conditions for Rolling Aluminum Alloy Al–Mg–Sc Based on FEM Modeling

Modelling of the Rolling Process of Titanium Alloy Tube Billets in Laboratory Conditions on a RSP 14-40 Rolling Mill

Innovative Methodology for Physical Modelling of Multi-Pass Wire Rod Rolling with the Use of a Variable Strain Scheme

Effect of radial shear rolling on grain refinement and mechanical properties of the Al–Mg–Sc alloy

Advanced Technology for Preparing Bar from Medical Grade Ti-Zr-Nb Superelastic Alloy Based on Combination of Radial-Shear Rolling and Rotary Forging

Effect of Radial Shear Rolling on the Structure and Mechanical Properties of a New-Generation High-Strength Aluminum Alloy Based on the Al – Zn – Mg – Ni – Fe System

Using the Radial Shear Rolling Method for Fast and Deep Processing Technology of a Steel Ingot Cast Structure

A study of conditions of surface defects formation when bar rolling at a bar and wire mill and methods of their elimination

Modeling the Evolution of Casting Defect Closure in Ingots through Radial Shear Rolling Processing

Continuous Casting and Rolling for Aluminum Alloy Wire and Rod

Development of Advanced Technologies for the Production of Innovative Materials with a Submicrocrystalline Structure by Methods of Severe Plastic Deformation

Formation of Microstructure and Mechanical Properties of Co-Cr-Mo Alloy by Hot Forging and Subsequent Radial Shear Rolling

Determining Conditions for Thermoplastic Processing Guaranteeing Receipt of High-Quality Wire Rod for Cold Upsetting using Numerical and Physical Modelling Methods

Deformation mechanism of ZK60 magnesium bars during radial forging: Mathematical modeling and experimental investigation

Effect of warm forming process parameters on 42CrMo4 skew rolled bar mechanical properties and microstructure

Analysis of the Effects of an Unconventional Rolling Process under Cumulative Plastic Deformation Conditions

Numerical simulation of cold longitudinal asymmetric rolling process

Improving the quality of cold-rolled deformable aluminum alloy billets

A Polycrystal Plasticity Based Thermo-Mechanical-dynamic Recrystallization Coupled Modeling Method and Its Application to Light Weight Alloys