Abstract:A new way on the magnitude and position of direction change of shear deformation resulted from rolling geometry and friction described by two parameters of Rf and Rp changed with practical rolling conditions is established for analyzing rolling textures. It is found that {001} <110> shear texture is dependent on the parameters of Rf and Rp, and rolling neutral angle is at the middle point of rolling deformation zone, i.e. Rp = 0.5, which favors development of {001}<110> shear texture. The results show that the rolling textures simulated by taking into account of Rf and Rp changed with practical rolling conditions are in better agreement with the measured than that of Rp = 0.5 in rolled high purity Al. Introduction Rolling textures and deformation microstructures have been demonstrated to be changed with rolling geometry and friction on contact surfaces between rollers and sample in previous investigations [1, 2, 3], in which {001}<110> shear texture and micro-shear bands with Cube orientation were found in rolled high purity aluminum with heavier rolling friction. However, the presented ways on effect of rolling geometry and friction on rolling texture components were either simple or complex, and rolling neutral angle position was hypothesized to be at the middle point of rolling deformation zone (RDZ) in literatures [4, 5, 6]. In current investigation, shear deformation can conventionally be changed with practical rolling conditions including rolling geometry and friction, especially, the position of direction change of shear deformation, i.e., rolling neutral angle, is not hypothesized to be at the middle point of RDZ per pass. Development of rolling textures in high purity Al rolled up to different total engineering strains is studied by experiment and modeling. Application of practical conditions on rolling texture modeling Practical Rolling conditions. All that rolling conditions are constrained by three angles, α, β and γ, and a relationship of the three angles can be described as known as

Analysis of Temperature-Deformation Conditions for Rolling Aluminum Alloy Al–Mg–Sc Based on FEM Modeling

DEVELOPMENT OF THE TECHNOLOGICAL PROCESS OF ROLLING BARS IN THE NEW DESIGN RADIAL SHEAR MILL BY USING PHYSICAL MODELING

Effect of radial shear rolling on grain refinement and mechanical properties of the Al–Mg–Sc alloy

Friction-mediated tuning of shear deformation and microstructure in asymmetrically rolled Mg–1Gd alloy strips

Calculation and analysis of rolling force during aluminum alloy thick plate snake/gradient temperature rolling with different roll diameters

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Numerical simulation of cold longitudinal asymmetric rolling process

The Coupled Temperature Field Model of Difficult-to-Deform Mg Alloy Foil High-Efficiency Electro-Rolling and Experimental Study

Investigation on Temperature Change of Cold Magnesium Alloy Strips Rolling Process with Heated Roll

Finite element simulation of hot cladding parameters for thin-sheet rolled products made of experimental Al–2%Cu–2%Mn alloy

An inclusive comparative study on the influences of the ring rolling process at elevated temperatures on the mechanical properties and microstructures of two centrifugally cast light alloys

Study on Asymmetric Rolling Process Applied to Aluminum Alloy Sheets

Static softening behavior of 316L stainless steel under flexible rolling process

Research on Hot Deformation Rheological Stress of Al-Mg-Si-Mn-Sc Aluminium Alloy

Microstructural Evolution and Mechanical Properties of Pure Aluminum upon Multi-Pass Caliber Rolling

Deformation Microstructure and Characteristics of Cast-Rolling and Normal Rolling AZ31 Magnesium Alloy Sheets

Effect of Direction Change of Shear Deformation on the Textures in Rolled High Purity Al

Finite Element Modeling and Experimental Verification of a New Aluminum Al-2%Cu-2%Mn Alloy Hot Cladding by Flat Rolling

Strain Hardening of 1565ch, AMg6, 01570, and 1580 Aluminum Alloys in the Process of Cold Rolling of Plates

Effect of Radial Shear Rolling on the Structure and Mechanical Properties of a New-Generation High-Strength Aluminum Alloy Based on the Al – Zn – Mg – Ni – Fe System

Analytic Numerical Modeling for Thermal Mechanical Processing of Plate under Rolling