Abstract:Magnesium-based alloys show significant promise for widespread applications owing to their lightweight nature and improved mechanical properties achieved through grain refinement via hot rolling. This investigation focuses on Mg-xAl-yCa-zMn (AXM alloys), pre-heated to temperatures of 350, 400, and 450 °C and processed via both single-pass differential speed rolling (DSR) and conventional rolling (CR). The key findings reveal the interplay between processing temperature, strain rate during single-pass rolling, and an innovative approach for incorporating varying amounts of Ca, influencing grain size, quantity of dynamic recrystallization (DRX) grains, and overall mechanical properties, including strength and ductility. A noteworthy observation is the positive correlation between an increase in the total reduction during hot rolling and a higher fraction of DRXed grains. This leads to a significant reduction in average grain size, diminishing from 60.3 ± 54.3 μm to 19.5 ± 14.2 μm at 40%, nearly a third the size of T4 grains (the initial homogenized microstructure of the AXM alloys). The resultant material strength experiences a doubling from an average of 125 ± 10.2 MPa (T4) to 260 ± 25.8 MPa (DSR rolled at 40%) for the AXM alloys with potential improvement in the ductility depending on rolling speed conditions. This study also aims to analyze the combination of rolling temperature, rolling speed, thickness reduction, speed difference and Ca content implemented across a wide range of temperatures and strain rates to provide a holistic approach to the processing parameters affecting the microstructure and mechanical properties of AXM alloys. Furthermore, this study provides a deeper understanding of DRX mechanisms, including continuous DRX (CDRX), discontinuous DRX (DDRX), and twinning induced DRX (TDRX), while each of these mechanisms plays a distinct role in the overall enhancement of formability and performance of magnesium alloys.

Friction-mediated tuning of shear deformation and microstructure in asymmetrically rolled Mg–1Gd alloy strips

Deformation mechanisms and recrystallization behavior of Mg-3Al-1Zn and Mg-1Gd alloys deformed by electroplastic-asymmetric rolling

Enhanced rollability of Mg alloys by directly activated { 10 1 ̄ 2 } twinning during asymmetric rolling: Experiments and finite element analysis

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling

Asymmetric Rolling of Interstitial-Free Steel Using Differential Roll Diameters. Part I: Mechanical Properties and Deformation Textures

Influence of Processing Temperature and Strain Rate on the Microstructure and Mechanical Properties of Magnesium Alloys Processed by Single-Pass Differential Speed Rolling

Effect of radial shear rolling on grain refinement and mechanical properties of the Al–Mg–Sc alloy

Influence of Asymmetric Rolling Process and Thickness Reduction on the Microstructure and Mechanical Properties of the Al–Mg-Si Alloy

The formation of the cross shear bands and its influence on dynamic recrystallization and mechanical properties under Turned-Reverse Rolling

Improvement of Formability of Mg–3Al–1Zn Alloy Strip by Electroplastic-Differential Speed Rolling

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

Enhanced mechanical properties of AZ91 magnesium alloy by asynchronously large-strain high-efficiency rolling with bimodal grain structure

Effect of rolling deformation on microstructure and mechanical properties of Mg–Y–Nd–Al alloy

Microstructure and Texture Evolution of Mg-3Zn-1Al Magnesium Alloy During Large-Strain Electroplastic Rolling

Strengthening a Medium-Carbon Low-Alloy Steel by Nanosized Grains: The Role of Asymmetrical Rolling

Effect of Al addition and rolling reduction on microstructure and texture evolution of Mg–3Sn alloy during high-speed rolling

Recrystallization and Anisotropy of AZ31 Magnesium Alloy by Asynchronous Rolling

Effect of Dual Deformation Processes on the Microstructure and Mechanical Properties of Low-Alloyed Mg-Zn-Ca-Mn Alloy

Effect of ultrasonic surface rolling process on microstructure and properties of rolled Mg-Y-Nd-Zr alloy

Effect of differential temperature on the interfacial microstructure evolution and mechanical properties of asymmetrically rolled Mg/Al composite plates

The effect of grain size on deformation modes and deformation heterogeneity in a rolled Mg-Zn-Ca alloy