Abstract:A new way on the magnitude and position of direction change of shear deformation resulted from rolling geometry and friction described by two parameters of Rf and Rp changed with practical rolling conditions is established for analyzing rolling textures. It is found that {001} <110> shear texture is dependent on the parameters of Rf and Rp, and rolling neutral angle is at the middle point of rolling deformation zone, i.e. Rp = 0.5, which favors development of {001}<110> shear texture. The results show that the rolling textures simulated by taking into account of Rf and Rp changed with practical rolling conditions are in better agreement with the measured than that of Rp = 0.5 in rolled high purity Al. Introduction Rolling textures and deformation microstructures have been demonstrated to be changed with rolling geometry and friction on contact surfaces between rollers and sample in previous investigations [1, 2, 3], in which {001}<110> shear texture and micro-shear bands with Cube orientation were found in rolled high purity aluminum with heavier rolling friction. However, the presented ways on effect of rolling geometry and friction on rolling texture components were either simple or complex, and rolling neutral angle position was hypothesized to be at the middle point of rolling deformation zone (RDZ) in literatures [4, 5, 6]. In current investigation, shear deformation can conventionally be changed with practical rolling conditions including rolling geometry and friction, especially, the position of direction change of shear deformation, i.e., rolling neutral angle, is not hypothesized to be at the middle point of RDZ per pass. Development of rolling textures in high purity Al rolled up to different total engineering strains is studied by experiment and modeling. Application of practical conditions on rolling texture modeling Practical Rolling conditions. All that rolling conditions are constrained by three angles, α, β and γ, and a relationship of the three angles can be described as known as

The formation of the cross shear bands and its influence on dynamic recrystallization and mechanical properties under Turned-Reverse Rolling

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling

Reduction per pass effect on texture traits and mechanical anisotropy of Mg–Al–Zn–Mn–Ca alloy subjected to unidirectional and cross rolling

Friction-mediated tuning of shear deformation and microstructure in asymmetrically rolled Mg–1Gd alloy strips

Multiple-twinning induced recrystallization and texture optimization in a differential-temperature-rolled AZ31B magnesium alloy with excellent ductility

Dynamic recrystallization of a wrought magnesium alloy: Grain size and texture maps and their application for mechanical behavior predictions

The improvement on mechanical anisotropy of AZ31 magnesium alloy sheets by multi cross-rolling process

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

Deformation mechanisms and recrystallization behavior of Mg-3Al-1Zn and Mg-1Gd alloys deformed by electroplastic-asymmetric rolling

Effect of Al addition and rolling reduction on microstructure and texture evolution of Mg–3Sn alloy during high-speed rolling

Dynamic recrystallization mechanism and near-isotropic mechanical properties of WE43 magnesium alloy sheets rolled at different temperatures

Evolution of the Microstructure and Mechanical Properties of AZ31 Magnesium Alloy Sheets during Multi-Pass Lowered-Temperature Rolling

Deformation mechanism, orientation evolution and mechanical properties of annealed cross-rolled Mg-Zn-Zr-Y-Gd sheet during tension

Influence of Processing Temperature and Strain Rate on the Microstructure and Mechanical Properties of Magnesium Alloys Processed by Single-Pass Differential Speed Rolling

Dynamic precipitation and twinning-induced dynamic recrystallization in Mg–6Al–3Sn–1Zn alloy during multi-pass high-speed rolling

Significantly improvement in formability and ductility of AZ31 Mg alloy by differential temperature rolling

Effect of Direction Change of Shear Deformation on the Textures in Rolled High Purity Al

The effect of grain size on texture evolution and mechanical properties of an AZ31 magnesium alloy during cold-rolling process

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy