Abstract:The Mg-Gd-Y-Zn-Zr sheets with different accumulative rolling reduction were successfully prepared through the multi-passes hot rolling process. The accumulative rolling reduction significantly affects the mechanical properties of the resulting sheets through altering the fraction of dynamic recrystallization (DRX) grains and distribution of the broken interdendritic 14H-LPSO phase. In addition, the precipitated equilibrium β phase at grain boundaries can facilitate the DRX process through the particle-stimulated nucleation (PSN) mechanism. The sub-grain boundaries formed in the vicinity of the grain boundaries and within the coarse deformed grains, and then transformed into the high-angle grain boundaries (HAGBs) through incorporating the adjacent dislocation. The coarse deformed grains were also divided into several grains by the formation of HAGBs and the DRX grains at grain boundaries also spread into the coarse deformed grains, and thus the fraction of the DRX grains improved with the increase of the accumulative rolling reduction. The ambient temperature tensile strength anisotropy of the resulting sheets increases with further accumulative rolling reduction. The effectively broken interdendritic 14H-LPSO phases, which acts as the reinforcing short-fiber, significantly strengthen the tensile yield strength along the RD due to its decreased aspect ratio (d/l) and more dispersed distribution aligned along the RD. Thus, the tensile yield strength along the RD demonstrated the higher increment than that along the TD and 45° with increasing accumulative rolling reduction. The broken interdendritic 14H-LPSO phases aligned along the RD also contribute to the higher fracture elongation along the 45° due to its alignment parallel to the resolved maximum shear stress during tension. Furthermore, the larger accumulative strain is conducive to decreasing the tensile anisotropy of the resulting sheets at elevated temperature.

Improvement of Formability of Mg–3Al–1Zn Alloy Strip by Electroplastic-Differential Speed Rolling

Mg–3Al–1Zn alloy strips processed by electroplastic differential speed rolling

Deformation mechanisms and recrystallization behavior of Mg-3Al-1Zn and Mg-1Gd alloys deformed by electroplastic-asymmetric rolling

Research of Electroplastic Rolling of Az31 Mg Alloy Strip

Enhanced Rollability of Mg-3al-1zn Alloy by Pulsed Electric Current: A Comparative Study

Significantly improvement in formability and ductility of AZ31 Mg alloy by differential temperature rolling

Achieving single-pass high-reduction rolling and enhanced mechanical properties of AZ91 alloy by RD-ECAP pre-processing

Obtaining Heterogeneous Microstructure and Enhanced Mechanical Properties in ECAP-Processed AZ61 Alloys via Single-Pass Rolling with Increased Rolling Reduction

Friction-mediated tuning of shear deformation and microstructure in asymmetrically rolled Mg–1Gd alloy strips

Enhanced rollability of Mg alloys by directly activated { 10 1 ̄ 2 } twinning during asymmetric rolling: Experiments and finite element analysis

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy

Property Improvements in Fine–grained Mg–Zn–Zr Alloy Sheets Produced by Temperature–step–down Multi–pass Rolling

Microstructure and Texture Evolution of Mg-3Zn-1Al Magnesium Alloy During Large-Strain Electroplastic Rolling

Microstructure and mechanical property of multi-pass low-strain rolled Mg-Al-Zn-Mn alloy sheet

Enhanced Mechanical Properties of Extruded Mg–Y–Zn Alloy Fabricated Via Low-Strain Rolling

Effect of Rolling Reduction on Microstructure and Mechanical Properties of Mg-9Gd-3Y-0.5Zr Alloys

Improved Ductility of Mg–Zn–Ce Alloy by Hot Pack-Rolling

Effect of Dual Deformation Processes on the Microstructure and Mechanical Properties of Low-Alloyed Mg-Zn-Ca-Mn Alloy

Effects of Accumulative Rolling Reduction on the Microstructure Characteristic and Mechanical Properties of Mg-Gd-Y-Zn-Zr Sheets Processed by Hot Rolling

Achieving Outstanding Combination of Strength and Ductility of the Al-Mg-Li Alloy by Cold Rolling Combined with Electropulsing Assisted Treatment