Abstract:An analysis was performed on the temperature, rate and force parameters of the hot cladding process for the experimental Al–2%Cu–2%Mn alloy with technically pure aluminum grade 1050A, as well as on the stress-strain state of the metal in the deformation zone at reductions of 30, 40, and 50 %. Plastometric tests were conducted within the temperature range of 350–450 °C, strain rates of 0.1–20 s –1 , and true strain of 0.1–0.9, and coefficients for calculating the flow stress of the experimental alloy were determined. The thermal conductivity of the Al–2%Cu–2%Mn alloy under hot deformation conditions at temperatures of 350, 400, and 450 °C was theoretically calculated to be 161, 159, and 151 W/(m·K), respectively. The study of the cladding process on a two-high rolling mill was carried out using the QForm finite element simulation software. It was found that when the metal of the cladding layer comes into contact with the roll, its temperature decreases by approximately 100 °C, with the temperature across the height of the composite equalizing within 20–30 ms after exiting the deformation zone. The rolling force is evenly distributed between the two rolls in all cases considered, while the rolling torque on the roll on the cladding layer side is half that on the roll contacting the base layer, which is characteristic of asymmetric rolling. Points characterized by optimal bonding conditions of the rolled layers were identified, located at 10 % and 70 % of the deformation zone length along the rolling axis, where normal stresses significantly prevail over shear stresses. It was determined that the formation of these areas is due to the nature of plastic flow, including the presence of a non-deforming hard layer and a sticking zone.

Finite Element Modeling and Experimental Verification of a New Aluminum Al-2%Cu-2%Mn Alloy Hot Cladding by Flat Rolling

Finite element simulation of hot cladding parameters for thin-sheet rolled products made of experimental Al–2%Cu–2%Mn alloy

Numerical Simulation of Multi-Pass Hot Rolling of TA1/Q235B Clad Plates

Digital simulation of aluminum alloy slab rolling with low relative reduction

Microstructural Evolution and Mechanical Properties of Pure Aluminum upon Multi-Pass Caliber Rolling

Interface Characteristics and Bonding Performance of the Corrugated Mg/Al Clad Plate

Effect of cumulative deformation and interlayer mechanical properties on bonding strength of corrugated interface steel/aluminum composite plate

Microstructure and Mechanical Properties of Aluminum Clad Steel Plates by Cold Rolling and Annealing Heat Treatment

Research on corrugated interface formation mechanism and mechanical properties of the CFR flat Mg/Al clad plate

Numerical Simulation of Cast-rolling Process for Copper-Aluminum Composite Plate

Microstructure evolution, mechanical properties and tailoring of coefficient of thermal expansion for Cu/Mo/Cu clad sheets fabricated by hot rolling

Interface evolution and strengthening of two-step roll bonded cu/Al clad composites

Twin-Roll Casting of Aluminum-Steel Clad Strips: Static and Dynamic Mechanical Properties of the Composite

Cold Rolling Technology Optimization for EN AW 4343/3003/4343 Cladded Aluminum Alloys and Influence of Parameters on Microstructure, Mechanical Properties and Sustainable Recyclability

Experimental and numerical investigations into the ductile fracture during the forming of flat-rolled 5083-O aluminum alloy sheet

A study on the microstructural evolution of copper/aluminum composite strips fabricated by micro flexible rolling

Characterization and constitutive analysis-based crystal plasticity of warm flow and fracture behaviours of 2060 Al-Cu-Li alloy

Study on the effects of initial temperature and thickness ratio of component metals on the preparation of aluminum/steel clad plates by the new different temperature rolling method

Studying the Effect of Cold Rolling and Heat Treatment on the Microstructure and Mechanical Properties of the Fe36Mn20Ni20Cr16Al5Si3 High Entropy Alloy

Velocity Field Analysis of Bonding Interface on Cold-Rolled Copper/Aluminum Composite Plate

Formation mechanism of dynamic multi-neutral points and cross shear zones in corrugated rolling of Cu/Al laminated composite