Abstract:The present study investigated influences of the Al3Sc particle content on the evolution of bimodal grain structure and mechanical properties at both room and elevated temperatures of Al–7Mg–Sc alloys processed by hard-plate rolling (HPR). Bimodal grain structures were obtained in HPRed Al–7Mg–Sc alloys where ultrafine/fine grains decreased in size and increased in amount with increasing volume fraction of Al3Sc precipitates. The formation and evolution of bimodal grain structure are associated with (i) the different stability of various-orientated grains, and (ii) the volume fraction of Al3Sc precipitates. Ultrafine/fine (sub) grains form preferentially along grain boundaries (GBs) of <001>//normal direction (ND)- and <111>//ND-oriented coarse grains during HPR. In contrast, the <101>//ND-oriented coarse grains show relatively high stability nearly without subdivision. Furthermore, increased volume fraction of Al3Sc precipitates in Al–7Mg–0.4Sc promotes dislocation accumulation, favoring recrystallization nucleation, and meanwhile restricts grain growth, which results in more and refined ultrafine/fine grains. Thereby, the refined grain structure and increased volume fraction of Al3Sc precipitates in the Al–7Mg–0.4Sc alloy contribute to improved room-temperature yield strength (YS) and elongation, i.e. ~482 MPa and ~8%, which is much higher than that of ~420 MPa and ~4% in the binary Al–7Mg alloy. Meanwhile, Al–7Mg–0.4Sc exhibited higher hardness when annealed at 150–300 °C and also higher YS when subjected to a tensile test at ≤ 200 °C due to the more stabilized grain structure pinned by dispersed Al3Sc and additional strengthening effect from Al3Sc precipitates. Nevertheless, when subjected to a tensile test at ≥ 250 °C, the Al–7Mg–0.4Sc alloy exhibited much lower YS than binary Al–7Mg. The transition could be explained by more favored grain boundary sliding (GBS) and great dislocation loss, due to the easier occurrence of dynamic recrystallization (DRX) in Al–7Mg–0.4Sc during tensile test at elevated temperatures.

Effect of Rolling Reduction on Microstructures and Mechanical Properties of Sc-Containing Al-3.2Cu-1.5Li Alloy

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Effect of Rolling Temperature on Microstructure and Properties of Al-Mg-Li Alloy

EFFECT OF Sc ON MICROSTRUCTURE AND PROPERTIES OF Al-Li-Cu-Mg-Zr ALLOY

Influences of the Al3Sc particle content on the evolution of bimodal grain structure and mechanical properties of Al–Mg–Sc alloys processed by hard-plate rolling

Microstructures evolution and mechanical properties disparity in 2070 Al-Li alloy with minor Sc addition

Microstructure evolution and mechanical properties of Al−3.6Cu−1Li alloy via cryorolling and aging

Effect of Sc contents on the mechanical properties and damping capacity of Al-Zn-Mg-Cu-Zr-Sc alloys with different grain structures

Effect of asymmetric rolling and subsequent ageing on the microstructure, texture and mechanical properties of the Al-Cu-Li alloy

Influence of Different Rolling Processes on Microstructure and Strength of the Al–Cu–Li Alloy AA2195

Effect of minor Sc additions on precipitation and mechanical properties of a new Al-Cu-Li alloy under T8 temper

Microstructure evolution, mechanical response, and corrosion resistance for a 2195 Al-Li alloy under different rolling reductions during cryorolling

Influence of Asymmetric Rolling Process and Thickness Reduction on the Microstructure and Mechanical Properties of the Al–Mg-Si Alloy

Effect of Pre-Rolling on Microstructure and Fatigue Crack Propagation Resistance of a Third-Generation Al-Li Alloy

Effect of Al addition and rolling reduction on microstructure and texture evolution of Mg–3Sn alloy during high-speed rolling

Effects of Cold Rolling Reduction Rate on the Microstructure and Properties of Cu-1.16Ni-0.36Cr Alloy after Thermo-Mechanical Treatment

Effects Of Rolling Process On Microstructure And Mechanical Property Of 7050 Aluminum Alloy

Microstructure evolution behavior and mechanical mechanisms in a near α-Zr alloy by cold rolling

Microstructure study of hot rolling nanosized in-situ Al2O3 particle reinforced A356 matrix composites

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy