Abstract:This paper investigates the behavior of transverse defects under significant total strain in conditions of complex vortex metal flow implemented through the radial shear rolling (RSR) method. The aim of this study is to assess the applicability of RSR processing for the in-depth transformation of small ingots of special steel into bars, particularly for the manufacturing of structural elements in specialized construction projects such as nuclear power plants. Although a substantial total strain is anticipated to enhance the steel structure and contribute to defect closure, the question of the development or closure of potential casting defects remains unclear. To address this issue, model tests were conducted to simulate the implementation of RSR processing. Defect behavior data under very complex vortex metal flow and high strain conditions were obtained for the first time and have scientific merit. A small steel ingot with a 32 mm diameter, containing a simulated artificial defect in the form of a transverse through-hole with a 5 mm diameter, was employed. During rolling, the workpiece diameter was progressively reduced by 2 mm with each subsequent pass, reaching a final diameter of 20 mm. Additionally, to provide a more detailed visualization of the defect evolution process, the same defect was modeled in an aluminum bar over six passes, and changes in defect volume and shape were analyzed after each pass. A highly detailed 3D visualization of the actual defect evolution was achieved based on cross-sections from experimental workpieces. These data corresponded to the total strain levels obtained by finite element method (FEM) simulation. Notably, a consistent similarity was observed between the test results for both metals, revealing a reduction in defect volume of up to 67.7%. The deformational welding of defects in the outer sections, encompassing one-third of the rod’s radius, occurred in the initial passes. However, defects in the axial zone of the rods remained unclosed, lengthening and gradually decreasing proportionally to the elongation of the rod, akin to conventional rolling. Consequently, the radial shear rolling (RSR) method is unsuitable for ingots with substantial discontinuities in the axial zone post-casting. Nevertheless, the method ensures the total welding of defects located in the outer zones of the ingots, even with minor applied deformations and a slight decrease in the diameter of the deformed ingot. Such data were obtained for the first time and should contribute to future investigations in this field.

Using of Radial-Shear Rolling to Improve the Structure and Radiation Resistance of Zirconium-Based Alloys

Using the Radial-Shear Rolling Method for Casted Zirconium Alloy Ingot Structure Improvement

Effect of Radial Shear Rolling on the Structure and Mechanical Properties of a New-Generation High-Strength Aluminum Alloy Based on the Al – Zn – Mg – Ni – Fe System

Effect of radial shear rolling on grain refinement and mechanical properties of the Al–Mg–Sc alloy

Advanced Technology for Preparing Bar from Medical Grade Ti-Zr-Nb Superelastic Alloy Based on Combination of Radial-Shear Rolling and Rotary Forging

Evolution of Shear Bands in the Structure of a Zirconium-Based Amorphous Alloy during Rolling at Different Temperatures

Effect of ultrasonic surface rolling process on the microstructure and corrosion behavior of zirconium alloy in high-temperature water condition

Microstructures and Mechanical Properties of a Commercial Pure Zirconium during Rolling and Annealing at Different Temperatures

Enhanced thermal-mechanical properties of rolled tungsten bulk material reinforced by in situ nanosized Y–Zr–O particles

Effect of ultrasonic surface rolling process on microstructure and properties of rolled Mg-Y-Nd-Zr alloy

Effect of deformation processing on microstructure and mechanical properties of Ti-42Nb-7Zr alloy

Resarch on Microstructure and Property of Zirconium alloy in the Rotary forging process by GNN-FEM

Using the Radial Shear Rolling Method for Fast and Deep Processing Technology of a Steel Ingot Cast Structure

Microstructures and mechanical properties of Mg-15Gd-1Zn-0.4Zr alloys treated by ultrasonic surface rolling process

Microstructure evolution and mechanical properties of in-situ ZrB2/Al7085 nanocomposites during hot rolling deformation

DEVELOPMENT OF THE TECHNOLOGICAL PROCESS OF ROLLING BARS IN THE NEW DESIGN RADIAL SHEAR MILL BY USING PHYSICAL MODELING

Effect of Zr on microstructure evolution of Ti-Mo composite microalloyed steel during rolling

Effects of triaxial rolling on the microstructure and installation characteristics of reactor pressure vessel studs

Synergetic Strengthening of Grain Refinement and Texture in Gradient Zircaloy-4 by Surface Mechanical Rolling Treatment

Modeling the Evolution of Casting Defect Closure in Ingots through Radial Shear Rolling Processing

Influence of Lubrication Effect on Microstructure of Hot Extruded Nuclear Grade Zr-4 Alloy